KNECHT HV 205-1 Скачать руководство пользователя страница 30

Страница: 30 / 35

8. Care and maintenance

For all work on the grinding machine, observe the locally applicable
safety and accident prevention regulations as well as instructions in the
“Safety” and “Important notes” section of the operating instructions.

CAUTION

8.1 Cleaning

The circular knife grinding attachment must be cleaned after each sharpening, otherwise the
grinding sludge will dry and be difficult to remove.

After cleaning the circular knife grinding attachment, we recommend the products listed in the
lubricant table for care (chapter 8.1.1).

8.1.1 Lubrication table

Lubrication work

Interflon

Würth

SHELL

EXXON
Mobil

Cleaning and care of machine parts

Dry clean
stainless steel

Stainless steel
care spray

Risella 917

Marcol 82

Lubricating threads and sliding
surfaces

Fin Grease

Multi-purpose
grease

Gadus S2

Ronex MP

8.2 Maintenance plan (one-shift operation)

Interval

Assembly

Maintenance task

Daily

All surfaces

Clean with a soft cloth and care spray.

Weekly

Star handle threads

Lubricate with multi-purpose grease.

Guideways

Clean and lubricate with multi-purpose grease.

Annually

Contact the service department of KNECHT
Maschinenbau GmbH.

Содержание HV 205-1




































Результаты поиска

Содержание HV 205-1

Отзывы:

Похожие инструкции для HV 205-1

Бренды по названию

Популярные бренды

KNECHT HV 205-1, Руководство по эксплуатации

Результаты поиска

Содержание HV 205-1

Отзывы:

Похожие инструкции для HV 205-1

Бренды по названию

Популярные бренды