Knauer AZURA P 2.1S Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 47

background image

Legal Information

41

P 2.1S/P 4.1S user manual V6870, version 3.1

Available Pump Heads

Legal Information

Transport Damage

The packaging of our devices provides the best possible protection against
transport damage. Check the devices for signs of transport damage. In case you
notice damages, contact the Technical Support and the forwarder company
within three workdays.

Warranty Conditions

The factory warranty for the device is stipulated by contract. During the war-
ranty period, any components with material or design-related defects will be
replaced or repaired by the manufacturer free of charge. Please connect to our
website for further information on terms and conditions.

All warranty claims shall expire in the event that any unauthorized changes are
made to the device. This warranty also excludes the following:



accidental or willful damage



damage or errors caused by third parties that are not contractually related to
the manufacturer at the time the damage occurs



wear parts, fuses, glass parts, columns, light sources, cuvettes and other opti-
cal components



damage caused by negligence or improper operation of the device and dam-
age caused by clogged capillary



packaging and transport damage

Pump P 2.1S with 10 ml pump head (stainless steel)

APG90EA

Pump P 2.1S with 10 ml pump head (ceramic)

APG90EB

Pump P 2.1S with 10 ml pump head (Hastelloy-C)

APG90EC

Pump P 2.1S with 50 ml pump head (stainless steel)

APG90FA

Pump P 2.1S with 50 ml pump head (ceramic)

APG90FB

Name

Order number

10 ml pump head with stainless-steel inlay

AHB40

10 ml pump head with ceramic inlay

AHB32

10 ml pump head with Hastelloy-C inlay

AHB43

50 ml pump head with ceramic inlay

AHC22

50 ml pump head with stainless-steel inlay

AHC20

Name

Order number

«
...
39
40
41
42
43
...
»

Содержание AZURA P 2.1S
















































Отзывы:

Нет отзывов

Похожие инструкции для AZURA P 2.1S

Бренд: TapFlo Страницы: 35

Бренд: Waters Страницы: 111

Бренд: IBO Страницы: 22

Aeromax Piscine 10

Бренд: Thermor Страницы: 32

Бренд: IBAIONDO Страницы: 7

Бренд: Bard Страницы: 24

Бренд: Oilon Страницы: 68

Бренд: Daikin Страницы: 40

Бренд: samhydraulik Страницы: 9

Бренд: Trigano PISCINES Страницы: 13

Бренд: Rheem Страницы: 50

Бренд: Winston Страницы: 28

Бренд: Waterous Страницы: 7

Бренд: CleanCraft Страницы: 22

Бренд: Parkside Страницы: 122

Бренд: Quooker Страницы: 20

Wilo-Smart 25/4

Бренд: Wilo Страницы: 78

Бренд: Greenlee Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды