background image

1.

  Determine your preferred height by holding the top basket up in the cabinet, taking into account the drawer contents 

 

and any other obstructions (i.e. hinges).

2.

  Measure from the bottom mounting bracket of the basket to the floor of the cabinet. 

(Fig. 1)

, and then add 2" to get 

 

Measurement A.

3.

  Mark the approximate center of the back wall cabinet at Measurement A. Then at the same height, make a second mark 

 

about 4" to the left of the center. 

(Fig. 2)

4.

  With the installation template arrow pointing up, insert the right rear mounting socket into the template. The “A” side of 

 

the socket should face towards the center of the cabinet as shown. 

(Fig. 3)

 The “V” notch on the socket should align 

 

with the “V” notch on the template as shown. 

(Fig. 4)

 Press socket firmly until it is seated into the template. Repeat for 

 

the left rear mounting socket.

5.

  Press the locking button on the template and extend it to match the width of the basket by selecting 11", 14" or 17". 

 

(Fig. 5)

6.

  Peel the film from the sticky tape on the back of the rear mounting sockets.

7.

  Align the template with the marks on the back wall of the cabinet and center the template from left to right so there

 

is equal space on either side. Push the sockets firmly onto the back wall ensuring the tape is attached. 

(Fig. 6)

8.

  If you have a 1/4" thin back wall, continue to Step 9. Otherwise, skip to Step 14.

  

310371-B_A (0513)

2700 Oak Industrial Drive NE  

Grand Rapids, MI 49505 USA 

800.253.1561  |  616.459.3311

www.kv.com

©2014 Knape & Vogt. All rights reserved.
Knape & Vogt

 reserves the right to change specifications without notice. 

Made in U.S.A.

STACK KIT

Installation Instructions

Works with 11.5" to 19.75" wide cabinet openings

Tools Required

 

• Drill

 

• 1/8" Drill Bit

 

• 5/16" Drill Bit

 

• Screwdriver

 

• Tape Measure

Parts Included 

Qty.

 

A.

 Template 

1

 

B.

 Rear Mounting Sockets 

2

 

C.

 Front Mounting Brackets 

2

 

D.

 #6 x 5/8" Pan Head Screws  8

 

E.

 #6 x 3/4" Flat Head Screws  8

Face Frame with Wire Basket

Frameless with Wood Basket

Fig. 3

Fig. 4

Product Assemblies
 

STACKKIT-R-BLK

“V” Notch

Press

Measurement A

Fig. 5

Fig. 1

Fig. 2

2" = Measurement A

4"

x

x

Fig. 6

A.

C.

E.

B.

D.

Содержание STACKKIT-R-BLK










Отзывы: