KMT MTP-NT Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 68

KMT MTP-NT Скачать руководство пользователя страница 2

Version 2018-14-CN

2

Technical Data are subject to change without notice!

Safety notes

•

The device should only applied by instructed personnel.

•

The power head emits strong magnetic radiation at 30-60 kHz to a distance of 300 mm.
Therefore persons with cardiac

pacemakers

should

not work

with this device!

•

Magnetic data storage media should be kept in a distance of at least 3m from the power
head to avoid data loss. The same is valid for electromagnetic sensitive parts, devices and
systems.

•

Do

not place

the power head in the switched-on state

on metallic objects

, because this

results in eddy currents which could overload the device and strong heat up small objects.
Also the probe could be destroyed!

•

No metallic objects, other than the disc-type coil, should be located in the air gap of the
power head. The same applies to metallic parts within a radius of up to 50 mm in all
directions.

•

Do not use damaged or faulty cables!

•

Never touch in the area between shaft and inductive head, the rotating shaft itself or rotor
electronic contacts during operation!

•

This is a “Class A” system suitable for operation in a laboratory or industrial environment.
The system can cause electromagnetic interferences when used in residential areas or
environments. In this case the operator is responsible for establishing protective
procedures.

«
1
2
3
4
...
»

Содержание MTP-NT





































































Отзывы:

Нет отзывов