background image

MEP-4xxx Direct-Coupled Actuators (40 to 90 in-lb.) 

Applications Guide, AN0513A Rev. J

Troubleshooting

Auxiliary Switch Does Not Work

• 

Check the auxiliary switch setting. See 

Auxiliary 

Switch (MEP-4x2x/4x7x) on page 12

.

• 

Check the wiring. (See 

Wiring Issues on page 

10

.)

Fail-Safe Does Not Work

• 

After initial connection or reconnection to power 

on MEP-42x2/45x2/49x2 proportional models, 

proper fail-safe operation might be delayed 

up to 30 seconds (until the capacitors are fully 

charged).

• 

Check the Fail-Safe Direction switch. See 

Fail-

Safe Direction (MEP-42/45/49xx) on page 13

.

Feedback Does Not Work

•  Check the feedback 

switch setting. See 

Propor-

tional (MEP-4xx2) Models Setup on page 10

.

• 

Check the wiring. (See 

Wiring Issues on page 

10

.)

No Rotation

• 

After initial power-up, proportional fail-safe 

MEP-42x2/45x2/49x2 actuators delay enabling 

motor operation until the fail-safe capacitors are 

charged. No actuator rotation will take place for 

at least the first 30 seconds.

• 

Check that direction switches are fully engaged 

in the proper position. See 

Proportional 

(MEP-4xx2) Models Setup on page 10

 and 

Tri-State/2-Position Rotation Direction on page 

11

.

• 

Check that the shaft moves freely. (Press and 

hold the gear disengagement lever and manually 

rotate the shaft.)

•  Check for a tripped circuit breaker to the trans-

former (or power supply).

•  Check polarity and strength of input signal.
•  Check for proper supply voltage from the trans-

former (or power supply) and that it has enough 

capacity (VA) for all connected devices. See their 

respective data sheets and 

Tips for Connecting 

24-Volt Power Application Note (AN0604D)

.

• 

Check the wiring. (See 

Wiring Issues on page 

10

.)

Rotation in Wrong Direction

•  For proportional models, check the position of 

the direction 

switch (Switch 2). See 

Proportional 

(MEP-4xx2) Models Setup on page 10

.

• 

For tri-state and tri-state/two-position mod

-

els, check the CW/CCW wiring and rotation 

direction switch if applicable. See 

Tri-State/2-

Position Rotation Direction on page 11

.

•  For fail-safe operation, check the Fail-Safe 

Direction switch. See 

Fail-Safe Direction (MEP-

42/45/49xx) on page 13

.

Stroke Range Is Wrong

•  For proportional models, check the auto-

mapping. See 

Proportional (MEP-4xx2) Models 

Setup on page 10

.

•  Check the adjustable stop.
•  Check the voltage from the controller or thermo-

stat.

Содержание MEP-4 Series















Отзывы: