background image

KMD–5210 Installation and Operation

Revision E

Configuration and programming

Configuring a controller with HCM

33

KMC digital network configuration

The entries in the table 

HCM Configuration Screen setup fields

 on page 33

 are 

required for controller-to-controller communications on a KMC controls 
digital network.

Table  4-1  HCM Configuration Screen setup fields

Setting

Description

Address

Enter the address that is assigned to the controller on the network. 
Valid numbers are 1–31. This address is also the BACnet MS/TP 
MAC address in KMD-5210–002 controllers.

Last Panel

Check this box only if the controller is assigned to the highest 
address number in the system. This controls token passing in the 
network. Last Panel is not applicable for Tier 1 controllers 
connected with Ethernet.

SubLAN A
SubLAN B
Main Network
BACnet

Sets the connection speed of the Tier1, Tier 2 or BACnet MS/TP port 
to which the LAN controller is connected. Set each baud to match 
the baud of the other controllers on each network.

Modem String For Firmware 4.0 and later: The string 

AT&A &B1 &C1 &D2 &H1 

&K0 &R1

 is stored in Flash memory and cannot be changed. Entries 

in 

Modem String

 are sent to the modem after the default string is 

sent. This provides a method to override settings in the default 
string. For example, entering ATS0=5 sets the modem to answer on 
the fifth ring.

Firmware earlier than 4.0: The controller automatically transmits the 
default initialization string 

AT&A &B1 &C1 &D2 &H1 &K0 &R1 

to 

the modem. The default string can be modified by making changes 
in 

Modem String

.

See 

Installing a modem interface

 on page 23

 for modem installation 

and switch settings.

Computer A

Use this field to set the communication speed if a PC is directly 
connected to this port.

Computer B

Use this field to set the communication speed if a PC is directly 
connected to this port. If you are using the modem port on the LAN 
controller, check the 

Modem

 box to indicate a modem is attached 

to the controller. If you have a modem attached, you cannot use the 
Computer B connector.

I/O Card 
Configuration

Use the fields in this area to enable communications with input or 
output cards connected to the controller. Click on the button to step 
through the choices. Input cards are connected to the controller 
starting at position #1; output cards are connected starting at 
position #8. If a port is unused, leave it marked as 

Unused

 in HCM.

Содержание KMD-5210







































Отзывы: