KMC Controls CSC 3000 Series Скачать руководство пользователя

Страница: 2 / 15

CSC-3000 Series Pneumatic VAV Reset Volume Controllers

Applications Guide, Rev G

Mounting

The CSC-3000 Series are position sensitive.

They

must be mounted and calibrated in either the

horizontal or vertical plane.

1. As near to the flow sensor pickup as is feasible,

connect the mounting bracket to the mounting

surface with two self-threading screws in the two

3/16" (5 mm) mounting holes. Be sure to leave

enough room to make connections.

2. Insert the controller, face down, up, right or left.

The controller must be installed and adjusted in

the same plane or readjustment will be necessary.

NOTE: These controllers are used on single and

dual duct applications. When working on

dual duct applications, it may be necessary

to work on one duct at a time.

NOTE: Any sequencing with other controllers,

valves, or pneumatic-electric relays must

be done with the controller’s reset range,

NOT the actuator’s spring range.

General Information

CSC-3000 Series Overview

These CSC-3000 series reset volume controllers are

designed for use on heating or cooling systems with

(normally open or normally closed) VAV terminal

units and (direct or reverse acting) thermostats.
They are sub-master air velocity controllers. Each is

equipped with separate adjustment knobs for mini-

mum and maximum airflow setpoints. Models are

available with various reset start points. A master

controller, typically a room thermostat, resets the

CSC-3000 between the minimum and maximum

velocity setpoints.
The universal design of the CSC-3000 series is in-

tended for new or replacement applications that call

for direct or reverse acting reset on normally open or

normally closed VAV terminal units.

More Information

For

specifications

, see the

CSC-3000 Series Data

Sheet

This Application Guide does not apply (complete-

ly) to the CSC-3014 (designed to work with CTC-

2100 Thermostats) or the CSC-3501/3505 (Linear

Volume Reset Controllers).

See their separate data

sheets and installation guides.

For adjusting start point and
span (upper and lower knobs)
review the respective sections

All adjustments
are CCW to
increase

All dimensions are

in inches (mm).

Содержание CSC 3000 Series
















Результаты поиска

Содержание CSC 3000 Series

Отзывы:

Похожие инструкции для CSC 3000 Series

Бренды по названию

Популярные бренды

KMC Controls CSC 3000 Series, Инструкция по применению

Результаты поиска

Содержание CSC 3000 Series

Отзывы:

Похожие инструкции для CSC 3000 Series

Бренды по названию

Популярные бренды