background image

KMC Controls

Revision  E

Operating the controller

Controls and Indicators

14

Ready LED

The green Ready LED indicates the state of the controller. This includes automatic 
addressing functions that are fully described in the guide 

MS/TP Addressing For 

BACnet Controllers.

Power up 

During controller initialization, the Ready LED is continuously 

illuminated for 5 to 20 seconds. Once initialization is complete, the Ready LED 
begins flashing to indicate normal operation.

Normal operation 

During normal operation, the Ready LED flashes a repeating 

pattern of one second on and then one second off.

Restart button acknowledge 

The restart button includes several functions for 

automatic addressing that are acknowledged with the Ready LED. When the restart 
button is pressed, the Ready LED illuminates continuously until either of the 
following take place:

• The restart button is released.
• The restart button time-out period is reached and a restart operation is 

complete. Restart button operations are listed in the following table.

Communications (Com) LED

The yellow Communications LED indicates how the controller is communicating 
with other controllers on the network.

Sole master 

Repeating pattern of a long flash and a short pause that repeats once a 

second. It indicates that the controller has either generated the token or is a sole MS/
TP master and has yet to establish communications with other MS/TP devices.

Token passing 

A short flash each time the token is passed. The frequency of the 

flash is an indication of how often the device receives the token.

Table  3-1  Ready LED patterns for restart button operations

Controller state

LED pattern

The controller is set as an automatic 
addressing anchor. The MAC in the 
controller is set to 3

A rapid repeating pattern of a short flash 
followed by a short pause. 

The controller has sent the automatic 
addressing lock command to the network

Two short flashes followed by a long 
pause. The pattern repeats until the restart 
button is released.

No restart operation

Ready LED remains unlit until the restart 
button is released.

Содержание BAC-7401



















Отзывы: