24in. Bending Brake
OWNER’S MANUAL
24in. Bending Brake
OWNER’S MANUAL
Important Safety Information
WARNING:
WORK AREA SAFETY
• Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well lit.
Cluttered, wet, or dark work areas can result in injury. Using the tool in confined work areas
may put you dangerously close to other cutting tools and rotating parts.
• Do not use the tool where there is a risk of causing a fire or an explosion; e.g., in the
presence of flammable liquids, gases, or dust. The tool can create sparks, which may ignite
the dust or fumes.
• Do not allow the tool to come into contact with an electrical source. The tool is not insulated
and contact will cause electrical shock.
• Keep children and bystanders away from the work area while operating the tool. Do not allow
children to handle the tool.
• Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in
your work area. Some of these hazards may be below the work surface hidden from your
view and may cause personal harm or property damage if unintentionally contacted.
PERSONAL SAFETY
• Stay alert, watch what you are doing, and use common sense when operating the tool. Do
not use the tool while you are tired or under the influence of drugs, alcohol, or medication. A
moment of inattention while operating the tool may result in serious personal injury.
• Dress properly. Do not wear loose clothing, dangling objects, or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair can be
caught in moving parts. Air vents on the tool often cover moving parts and should be avoided.
• Use safety apparel and equipment. Use ANSI-approved safety goggles or safety glasses with
side shields, or when needed, a face shield. Use a dust mask in dusty work conditions. Also
use non-skid safety shoes, hardhat, gloves, dust collection systems, and hearing protection
when appropriate. This applies to all persons in the work area.
• Do not overreach. Keep proper footing and balance at all times.
• Secure the work with clamps or a vise instead of your hand when practical. This safety
precaution allows for proper tool operation using both hands.
CAUTION
TOOL USE AND CARE
• Do not force the tool. Tools do a better and safer job when used in the manner for which they
are designed. Plan your work, and use the correct tool for the job.
• Check for damaged parts before each use. Carefully check that the tool will operate properly
and perform its intended function. Replace damaged or worn parts immediately. Never
operate the tool with a damaged part.
• Store the tool when it is not in use if it is not permanently installed. Store it in a dry, secure
place out of the reach of children. Inspect the tool for good working condition prior to
storage and before re-use.
• Use only accessories that are recommended by the manufacturer for use with your tool.
Accessories that may be suitable for one tool may create a risk of injury when used with
another tool.
• Keep guards in place and in working order. Never operate the tool without the guards in place.
• Inspect the tool for damage or excessive wear before each use. If you find damage do not
use the tool.
Specific Operation Warnings
WARNING:
• Pinch point hazard. Keep hands clear of bending die.
• Do not exceed the maximum bending capacity.
• Check that the bending brake is properly secured to a sturdy, level surface before each
use.
Assembly
No assembly required. The shrinker/stretcher is
fully assembled at the factory.
Inventory (Figure 2)
Assembly
To assemble your bending brake:
1. Securely mount the bending brake assembly
to a workbench or other stable surface, using
8mm hex bolts, flat washers, lock washersand
hex nuts. Mounting hole locations areindicated
in Figure 3.
2. Place the clamping angle on the bendingbrake
assembly.
2 of 6
3 of 6
Figure 1. 24" Bending Brake
Figure 2. inventory
a.
b.
c.
d.
e.
Bending Brake Assembly
Clamping Angle
Clamp Assemblies
Breaker Bar levers
Hardware Bag (not shown)
— hex Bolts M10-1.25 x 30
— hex nuts M10
— lock Washers 10mm
1
1
2
2
4
4
4
Figure 3.
Mounting hole locations (right side of
bending brake not shown)
