Safety instructions:
• Double insulated tools
are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still doesn't fit, contact a
qualified electrician to install a polarized outlet. Do not change the plug in any
way.
• Avoid body contact
with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
• When operating a power tool outside,
use an outdoor extension cord
marked “W-A” or “W.” These cords are rated for outdoor use and reduce the risk
of electric shock.
• Extension Cord Use:
A. Use only 'Listed' extension cords. If used outdoors, they must be
marked “For Outdoor Use.” Cords having 3-prong grounding type plugs and
mating receptacles are to be used with grounded tools.
B. Replace damaged or worn cords immediately.
C. Check the name plate rating of your tool. Use of improper size or gauge
of extension cord may cause unsafe or inefficient operation of your tool. Be sure
your extension cord is rated to allow sufficient current flow to the motor. For the
proper wire gauge for your tool, see chart.
CHART FOR MINIMUM WIRE SIZE OF EXTENSION CORD:
If in doubt, use larger cord. Be sure to check voltage requirements of the tool to your
incoming power source.
• Do not expose
power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
• Do not let your fingers
touch the terminals of plug when installing to or
removing from the outlet.
• Ground fault circuit interrupters.
If work area is not equipped with a
permanently installed Ground Fault Circuit Interrupter outlet (GFCI), use a plug-in
GFCI between power tool or extension cord and power receptacle.
PERSONALSAFETY
• Stay alert,
watch what you are doing and use common sense when operat-
ing a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while operat-
ing power tools may result in serious personal injury.
• Dress properly.
Do not wear loose clothing, dangling objects, or jewelry.
Keep your hair, clothing and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts. Air vents often cover moving
parts and should be avoided.
• Use safety apparel and equipment.
Use safety goggles or safety glasses
with side shields which comply with current national standards, or when
needed, a face shield. Use dust mask in dusty work conditions. This applies to
all persons in the work area. Also use non-skid safety shoes, hard hat, gloves,
dust collection systems, and hearing protection when appropriate.
• Avoid accidental starting.
Do not carry the power tool with your finger on
the switch. Ensure the switch is in the off position before plugging tool into
power outlet. In the event of a power failure, while a tool is being used, turn the
switch off to prevent surprise starting when power is restored.
• Do not overreach.
Keep proper footing and balance at all times.
• Remove adjusting keys or wrenches
before connecting to the power
supply or turning on the tool. A wrench or key that is left attached to a rotating
part of the tool may result in personal injury.
TOOL USE AND CARE
• Do not force the tool.
Tools do a better and safer job when used in the
manner for which they are designed. Plan your work, and use the correct tool
for the job.
• Never use a tool
with a malfunctioning switch. Any power tool that cannot
be controlled with the switch is dangerous and must be repaired by an autho-
rized service representative before using.
• Disconnect power
from tool and place the switch in the locked or off
position before servicing, adjusting, installing accessories or attachments, or
storing. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
• Secure work
with clamps or a vise instead of your hand to hold work when
practical. This safety precaution allows for proper tool operation using both
hands.
• Store idle tools.
When tools are not is use, store them in a dry, secure
place out of the reach of children. Inspect tools for good working condition prior
to storage and before re-use.
• Use only accessories that are recommended
by the manufacturer for your
model. Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
• Keep guards in place
and in working order
.
• Never leave tool
running unattended.
• Hold tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord.
Contact
with a “live” wire will make exposed metal parts of the tool “live” and shock the
operator.
3
4
