background image

 

 

SOFT 80,  SOFT 100 PELLET-BURNING STOVE 

EN - Rev. 1.0 

INTRODUCTION 

Important safety instructions 

Please read these instructions before installing and using the product. 

   

-

 

The appliance’s installation and initial start-up must be performed by skilled personnel trained in the relevant safety 
standards, who are responsible for the definitive installation of the appliance and its efficient operation. KLOVER S.r.l. 

shall not be held liable if these precautions are not observed. 

-

 

During the installation and use of the appliance, all local regulations – including those referring to national and European 

standards – must be observed. 

-

 

Connect the product’s flue gas outlet to a flue having the specifications described in the “Flue and its connection” 
section of this User Guide. 

-

 

The appliance is not suitable for installation on a shared flue system. 

-

 

If the flue should catch fire, use appropriate fire extinguishing equipment or call the fire brigade. 

-

 

Connect the product to an earthed power socket. Avoid using sockets controlled by switches or automatic timers. 

-

 

Do not use the power supply cable if damaged or worn. 

-

 

If a multiple socket is used, make sure that the total voltage of the connected devices does not exceed the rated voltage 

for the socket. Moreover, make sure that the total voltage of all devices connected to the socket does not exceed the 

maximum allowed level. 

-

 

The plug on the appliance’s power cable should be connected only once  the appliance has been assembled and 

installed. It should remain accessible after the installation, if the appliance is not fitted with a suitable and accessible 

two-pole switch. 

-

 

Do not use highly flammable substances to clean the appliance or its parts. 

-

 

Do not leave flammable containers and substances in the place where the appliance is installed. 

-

 

The appliance works exclusively with wood pellets and only with the hearth door shut. 

-

 

NEVER open the door of the appliance during normal operation.  

-

 

The use of poor quality pellets or any other material can damage the appliance’s operation, voiding the warranty and 
exempting the manufacturer from all liability.  

-

 

Do not use the appliance as an incinerator or for any use other than that for which it was designed. 

-

 

Do not use fuels other than those recommended. 

-

 

Do not use liquid fuels. 

-

 

The appliance becomes very hot to the touch during operation, particularly its outer surfaces; handle it with caution in 

order to avoid burns. 

-

 

Keep fuel and flammable materials at a safe distance. 

-

 

Only use original spare parts recommended by the manufacturer. 

-

 

Do not make any unauthorised modifications to the appliance. 

-

 

Do not touch the product’s hot components (glass-ceramic panel, flue pipe) during normal operation. 

-

 

Never touch the appliance when barefoot and/or with wet or damp parts of the body. 

-

 

Use  the  appropriate  button to  switch  off  the  electrical  panel.  Do not disconnect  the power  supply  cable  while  the 

appliance is operating. 

-

 

During the ignition phase and normal operation of the appliance, keep at a safe distance and do not remain standing 

in front of it. 

-

 

Keep children away from the appliance when it is running, as they could get burned by touching its hot components. 

-

 

Do not leave the packaging elements within reach of children or unassisted disabled persons. 

-

 

Children and inexperienced people must not be allowed to use the appliance. 

-

 

The appliance may be used by children aged 8 years and older and by people with reduced physical, sensory or mental 

capabilities, or who lack the necessary experience or knowledge of the appliance, provided that they are supervised 

or have been instructed on how to use the appliance safely and are aware of the attendant risks. 

-

 

Children should not play with the appliance. 

-

 

User maintenance and cleaning operations should not be carried out by unsupervised children. 

-

 

Do not use the appliance in ways other than those indicated in this user guide.  

-

 

The appliance is designed for indoor use only. 

-

 

This user guide constitutes an integral part of the appliance. If the product is sold to another user, this manual must be 

passed on to the new owner. 

 

Содержание SOFT 100


























































Отзывы: