background image

Service manual 

 

                            - 

29

 - 

9.3 Function 

Remote receiving 
Testing and forced running 
Position set for indoor unit wind vane 
LED displaying and alarm 
On or off Timer 
Protection for the compressor 
Current protection 
High temperature protection of indoor heat exchanger at heating mode 
Auto defrosting and heating recovery at heating mode 
Anti cold air at heating mode 

9.4 Protection 

9.4.1    3 minutes delay at restart for compressor. 
9.4.2    Sensor protection at open circuit and breaking disconnection 
9.4.3  Fan  Speed  is  out  of  control.  When  Indoor  Fan  Speed  is  too  high(higher  than  High 

Fan+300RPM)or too low(lower than 400RPM), the unit stops and LED displays failure information 
and can’t returns to normal operation automatically. 

9.4.4    Cross Zero signal error warning. If there is no Cross Zero signals in 4 minutes, the unit stops 

and LED displays failure information and can’t returns to normal operation automatically. 

9.4.5    The current protection of the compressor 

 

If  compressor  turns  off  for  continuously  4  times  due  to  current  protection  in  5  minutes  from 

Compressor    On,    the  unit  stops  and  LCD  displays  failure  information  and  can’t  returns  to  normal 
operation automatically. 

Содержание KSWM009-C113




















































Отзывы: