manualshive.com logo in svg

Klein Marine Systems, Inc. HydroChart 5000, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Klein Marine Systems, Inc. HydroChart 5000 Скачать руководство пользователя страница 46

3-10

   

CHAPTER 3 Preparation for Deployment

HydroChart 5000 Sonar Operations and Maintenance Manual

P/N 11210080, Rev. 02

To connect the TPU and the SonarPro Workstation:

1.

Connect the Ethernet cable to the LAN connector on the TPU and to either 
one of the two the ETHERNET connectors on the SonarPro Workstation.

2.

Connect the monitor to the DVI connector on the SonarPro Workstation and 
connect the monitor power supply to the AC power source.

3.

Connect the keyboard and the mouse to any two of the six USB connectors on 
the SonarPro Workstation.

4.

Connect a GPS to the NAV connector on the TPU. A user supplied RS-232 
serial cable is required where one end is terminated with a DB9 female 
connector and the other end is as required by the navigation system.

5.

Verify that the GPS is outputting NMEA-0183 formatted data strings at 
4800 baud, no parity, 8 data bits, and 1 stop bit. In addition, the GPS should be 
outputting the following messages:

• GLL or GGA

• VTG

• RMC (optional)

6.

Connect the deck cable to the TOWFISH connector on the TPU.

7.

Connect an AC power cable to the AC INPUT connectors on the TPU and the 
SonarPro Workstation and to the AC power source.

The following connections are optional:

8.

Connect the 1 PPS connector on the TPU to the 1 PPS output of the shipboard 
GPS. A user supplied BNC-to-BNC cable is required.

9.

Connect the T/F TRIG connector on the TPU to the trigger input of an 
external sonar system. A user supplied BNC-to-BNC cable is required. 

10.

Connect the TRIG A connector on the TPU to the trigger input of a USBL 
system. A user supplied BNC-to-BNC cable is required.

11.

Connect the COM B (Sound Velocity) connector to the sound velocity sensor 
if installed on the Sonar Head Unit.

12.

Connect the COM C (Motion Reference Unit) connector to the motion 
reference unit if available.

NOTE  

If 4800 baud is not available from the GPS, contact KMS customer 

service for instructions on how to reconfigure the system to accept a 
different baud rate. Refer to “Customer Service” on page xvii for 

information on how to contact KMS customer service.

Содержание HydroChart 5000



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды