Klein Marine Systems, Inc. HYDROCHART 3500 Скачать руководство пользователя

Страница: 70 / 86

B-4

APPENDIX B Configuring and Updating the Sonar Head Unit

HydroChart 3500 Sonar System Operations and Maintenance Manual

P/N 11210087, Rev. 03

If this window does not appear, turn the TIU off and then back on. The
window should now appear, but it may take up to 45 seconds to do so.

B.3 Updating the Sonar Head Unit Software

Updates to the Sonar Head Unit software are supplied as compressed archive files
and must reside on the PC.

To update the Sonar Head Unit software:

Connect the system components as described in “Connecting the System
Components” on page 3-5.

Turn on the PC and wait for the Windows desktop to appear.

Turn on the TIU by pressing the ON/OFF switch.

Start Linux TPU Updater

by double-clicking the Linux TPU Updater icon

on the Windows desktop

The

Klein Linux TPU Updater

dialog box opens.

Enter the Sonar Head Unit IP address in the

Enter TPU IP Address

text box if it

is different from the default address, or click

Default Addr

if it is the default. The

default address is 192.168.0.81. The address will already be displayed if it was
queried or changed as described in “Querying or Changing the Sonar Head Unit
IP Address” on page B-1.

Содержание HYDROCHART 3500























































































Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды

Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды