Klein Marine Systems, Inc. HYDROCHART 3500 страница 69 Скачать руководство пользователя

Страница: 69 / 86

Editing the Sonar Head Unit Startup File

B-3

B.2 Editing the Sonar Head Unit Startup File

The startup file for the Sonar Head Unit is startupCdi3000.ini.

To edit the startup file:

Connect the system components as described in “Connecting the System
Components” on page 3-5.

Turn on the PC and wait for the Windows desktop to appear.

Turn on the TIU by pressing the ON/OFF switch.

When the system is running, start Linux TPU Updater

by double-clicking the

Linux TPU Updater icon

on the Windows desktop

The

Klein Linux TPU Updater

dialog box opens:

Enter the Sonar Head Unit IP address in the

Enter TPU IP Address

text box if it

is different from the default address, or click

Default Addr

if it is the default. The

default address is 192.168.0.81. The address will already be displayed if it was
queried or changed as described in “Querying or Changing the Sonar Head Unit
IP Address” on page B-1.

Click

Edit startup.ini

Windows Notepad opens with the contents of the startupCdi3000.ini file
displayed.

Make the required changes to the startupCdi3000.ini file, and then exit Notepad.

Notepad exits and the changed file is saved. The Sonar Head Unit software
restarts and a window opens confirming the file update:

Содержание HYDROCHART 3500























































































Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды

Klein Marine Systems, Inc. HYDROCHART 3500, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HYDROCHART 3500

Отзывы:

Похожие инструкции для HYDROCHART 3500

Бренды по названию

Популярные бренды