background image

 

12 

when loading the boat and planning how far from 

shore you intend to go. 

 

6.

 

Personal Flotation Gear 

Always  make  sure  that  everyone  in  the  boat  is 

wearing  the  proper  Personal  Flotation  Device  (life 

jacket). 

 

 

OPERATING THE BOAT 

 

Launching Tips 

 

1.

 

When launching the boat from shore it is better  to 

enlist  the  help  of  a  bystander  or  passenger  to  help 

lift the boat and carry it to the water.  You can drag 

the boat, but carrying it will prevent excessive hull 

abrasion over time. 

 

2.

 

Be sure motor is tilted up to prevent damage when 

lowering the boat into the water. 

 

3.

 

If launching from a trailer, make sure to remove all 

tie downs before backing onto the launching ramp. 

 

4.

 

Make  sure  to  install  all  drain  plugs  before  putting 

the boat in the water. 

 

5.

 

When  entering  the  boat,  step  in  the  center  of  the 

boat so the boat remains stable. Do not step on the 

gunwale  (top  edge  of  the  side  of  the  boat),  which 

could cause the boat to tip. 

 

6.

 

After  the  boat  is  in  the  water,  but  before  leaving 

from  shore,  check  to  make  sure  the  boat  sits 

 

13 

reasonably level fore to aft and side to side.  If not, 

redistribute the items you have on board. 

 

7.

 

Be  especially  conscious  of  the  shore  condition.  

Sharp  rocks,  sharp  edges  on  break  walls,  concrete 

aprons, etc. can seriously chafe the hull if you drag 

or slide the boat over these surfaces. 

 

Mooring and Docking 

Avoid mooring or docking in very shallow water where the 

hull will hit bottom. 

 

Use  boat  fenders  or  other  cushioning  to  prevent  wave 

action from scraping the hull against the dock. 

 

Livewell Operation 

Fill  the  livewell  about  2/3  full  of  water. 

Do  not  overfill. 

The  excess  water  will  seep  between  the  hull  and  deck. 

Try to use cool water. Cooler water reduces the fish’s need 

for oxygen. Keep the lid closed when possible to help keep 

the water cool. 

 

The  10.2  model  has  a  recirculating  aerator  pump. 

Periodically cycle the pump.  The switch is on the electrical 

control panel. 

Drain the livewell by removing the drain plug. 

 

Lights (

Available on 10.2 model)

 

The lights should always be used if there are poor lighting 

conditions, e.g. dusk, dawn, fog etc. 

 

When  moving  under  poor  lighting  conditions,  the  bow 

and stern lights should be on.  

 

Содержание Bass Hound 10.2











Отзывы: