1. Select a dry, level site and clear the
ground of any sharp objects. Remove
the tent from its carry bag, untie fabric
ties and unroll the tent.
2. Spread out the floor of the inner tent
and peg out the four main corners.
Ensure that the tent is pulled taut
and square. Proceed to peg out the
remaining pegging points. Unzip and
open the doors to make erecting the
tent easier. Pitch the tent so it is in line
with the wind, never side on.
3. Open the pole bag and
assemble the poles
grouping them by colour.
Key:
GFR = Green Fibreglass Roof
RSR = Red Steel Roof
WSR = White Steel Roof
YSR = Yellow Steel Roof
GSR = Green Steel Roof
BSR = Black Steel Roof
YFR = Yellow Fibreglass Roof
YSL = Yellow Steel Leg
GSL = Green Steel Leg
REVERSE THE PROCEDURE TO LOWER THE TENT
Falcon 9 Tent
Model No. KC072-700
Your tent includes:
57 x pegs
13 x ropes
2 x GREEN fibreglass roof poles (1800mm x 11mm)
1 x RED steel roof pole (4080mm x 16mm)
2 x WHITE curved steel roof poles (1660mm x 19mm)
2 x YELLOW steel roof poles (1280mm x 16mm)
2 x GREEN steel roof poles (2040mm x 16mm)
2 x BLACK steel roof poles (1760mm x 16mm)
4 x YELLOW fibreglass roof poles (1020mm x 11mm)
4 x YELLOW steel leg poles (1950mm x 19mm)
4 x GREEN steel leg poles (1870mm x 19mm)
4 x black PORCH poles (1900mm x 16mm)
1 x black PORCH pole (2100mm x 16mm)
PITCHING INSTRUCTIONS
PACKING INSTRUCTIONS
Pack the poles and pegs into their bags, place into their separate
frame bag. Evenly lay out the fly inside the tent inner (this is best done
when the inner is still pitched) leaving all doors and windows open.
Replace the provided knuckle covers to protect the tent inner. Fold the
tent as shown below, forcing all of the air out the front door. Roll into
the tent bag provided.
Ensure the tent is completely dry and clean before storing away and
store it in a dry environment.
4. Take the two GREEN fibreglass roof poles and feed through the
pole sleeves.
5. Feed the RED steel roof pole through the pole sleeve along the
top centre of the roof and connect into the tri knuckle at either end.
Note: Make sure metal pin locks into slot on knuckle, you may
have to twist pole from side to side.
6. Take the two WHITE curved steel roof poles,
attach into the corner quad knuckle at the
front and back of the tent. Ensure pin locks
into knuckle. Attach the speed-clips.
7. Take the YELLOW, GREEN and BLACK
steel roof poles and one at a time lock them in
to the knuckles on the side and corner of the
tent roof. Attach the speed-clips.
8. Take the four YELLOW fibreglass roof
poles and insert into the tri and corner
quad knuckles.
9. Proceed to insert the GREEN fibreglass roof
poles into the quad knuckles.
10. Take the four GREEN steel leg poles and insert into the side quad
knuckle. This will take 2 people to assemble. It is recommended
to erect adjacent corners first. Fit the bottom of each pole onto the
corresponding pin at the base of the inner so that the tent stands.
11. Take the remaining four YELLOW steel leg poles and insert them
into the remaining corner quad knuckle openings. Attach the
speed-clips. The inner tent is now pitched.
12. Carefully pull the fly over the inner making sure the windows and doors
line up. Attach the ties on the underside of the fly around the frame.
This will secure the fly and help the tent to perform better in the wind.
Once the fly is secure, zip the doors up and peg out the fly ensuring
there is an adequate gap between the inner and fly.
13. Finally, rope out the guy ropes and fine tune the fly so it remains taut
and positioned correctly over the tent.
14. When pegging out the black PORCH poles, make sure the ropes are
at a 45° angle to pull the flap evenly. In light rain you can remove the
middle section to allow any water build-up to run off. In heavy rain you
may have to pull the door/porch flaps down to keep your tent dry.
The longest porch pole goes in the centre.
15. Please read the care instructions for more product information about
your tent.
To make sure the tent stays in place,
insert the pegs into the ground at a
45° angle.
Lay flat
Fold once
Fold twice
Roll
Fold again
RSR
WSR
WSR
GFR
GFR
YSL
YFR
YFR
YFR
YFR
YSR
GSR
BSR
YSR
GSR
BSR
YSL
YSL
GSL
GSL
GSL
GSL
YSL
Insert the pin into the end of
the steel ferrule.
Erect adjacent corners
of green steel leg poles
first.
