background image

 

 
 
 
 

 

!

  WARNING 

 

 
Equipment described herein is not designed for and 

MUST NOT

 be used for lifting, supporting, or transporting people, 

or for lifting or supporting loads over people. 
 
Equipment described herein should not be used in conjunction with other equipment unless necessary and/or 

required safety devices applicable to the system, crane, or application are installed by the system designer, system 

manufacturer, crane manufacturer, installer, or user. 
 
Modifications to upgrade, rerate, or otherwise alter this equipment shall be authorized only by the original equipment 

manufacturer. 
 
Equipment described herein may be used in the design and manufacture of cranes or monorails.  Additional 

equipment or devices may be required for the crane and monorail to comply with applicable crane design and safety 

standards.  The crane designer, crane manufacturer, or user is responsible to furnish these additional items for 

compliance.  Refer to CSA B167, “Overhead cranes, gantry cranes, monorails, hoists, and jib cranes”, ANSI/ASME 

30.17, “Safety Standard for Top-Running Single Girder Cranes”; ANSI/ASME B30.2 “Safety Standard for Top-

Running Double-Girder Cranes”; and ANSI/ASME B30.11 “Safety Standard for Underhung Cranes and Monorails”. 
 
If a below-the-hook lifting device or sling is used with a hoist, refer to ANSI/ASME B30.9, “Safety Standard for Slings” 

or ANSI/ASME B30.20, “Safety Standard for Below-the-Hook Lifting Devices”.

 

  
Hoists, trolleys, and cranes, used to handle hot molten material may require additional equipment or devices.  Refer to 

ANSI Z241.2, “Safety Requirements for Melting and Pouring of Metals in the Metal Casting Industry”. 
 
The system designer, system manufacturer, crane designer, crane manufacturer, installer, or user is responsible to 

assure that the installation and associated wiring of these electrical components is compliant with the applicable 

provincial codes. 
 
Failure to read and comply with any one of the limitations noted herein can result in serious bodily injury or death, 

and/or property damage.

 

 

Содержание SMR2Q Series

























































Отзывы: