background image

6

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT: 

Installer: Leave Installation Instructions with the homeowner.

Homeowner: Keep Installation Instructions for future 
reference. Save these Installation Instructions for the local 
electrical inspector’s use.

TOOLS NEEDED: 

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here. 

PARTS NEEDED:

Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

Order factory panels, make custom panels or consult a 
qualified cabinetmaker or carpenter to make the panels. 

Classic Series: Order factory panels, make custom panels, or 
consult a qualified cabinetmaker or carpenter to make the 
panels. See “Classic Series Custom Panels” for more 
information. 

Overlay Series: Make custom panels, or consult a qualified 
cabinetmaker or carpenter to make the panels. See “Overlay 
Series Custom Panels and Handle Kits” for more information.

Architect

®

 and Complete Series are shipped complete. 

If you are connecting the water line directly to copper tubing 
and not to a shutoff valve, you need a ferrule, a union, and a 

¹⁄₄

" (6.35 mm) compression fitting. 

Location Requirements

The refrigerator can be recessed in an opening between cabinets 
or installed at the end of a cabinet run using a side panel to 
enclose the refrigerator.

IMPORTANT:

Observe all governing codes and ordinances. 

It is recommended that you do not install the refrigerator near 
an oven, radiator, or other heat source. 

Do not install in a location where the temperature will fall 
below 55°F (13°C).

Floor must support the refrigerator weight, more than 600 lbs 
(272 kg), door panels and contents of the refrigerator. 

Ceiling height must allow for side tipping radius. See “Tipping 
Radius.”

Location should permit door to open fully. See “Door Swing 
Dimensions.” 

Location must permit top grille removal. See “Opening 
Dimensions.”

Opening Dimensions

To avoid tipping during use, the solid soffit must be within 1" 
(2.5 cm) maximum above the refrigerator. If the solid soffit is 
higher than 1" (2.5 cm) or one is not available, then the 
refrigerator must be braced. 

If the anti-tip boards are needed, they must be attached to 
the rear wall studs 80" to 90" (203 cm to 229 cm) above the 
floor. See “Install Anti-Tip Boards” for more information.

NOTE: A clearance of 

¹⁄₂

" (1.3 cm) must be maintained above 

the top grille in order for the top grille to be removed.

Hand drill or electric drill 
(properly grounded)

Drill bits

Two adjustable wrenches

Phillips screwdriver

Small level

Appliance dolly

Torx

®†

T27 screwdriver

¹¹⁄₃₂

" nut driver

³⁄₈

" and 

¹⁄₂

" open-end 

wrenches

⁵⁄₃₂

" Allen wrench

¹⁄₄

" and 

⁵⁄₁₆

" socket drivers

Tape measure

Utility knife

†®TORX is a registered trademark of Textron Innovations Inc.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as 
gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

¹⁄₂

"

(1.3 cm)

Содержание KSSC36FT - Architect Series II 21.1 cu. Ft. Built
















Отзывы: