background image

8

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install 

refrigerator.
Failure to do so can result in back or other injury.

Remove the Packaging

   Remove tape and glue residue from surfaces before turning on 

the refrigerator. Rub a small amount of liquid dish soap over 

the adhesive with your fingers. Wipe with warm water and dry.

   Do not use sharp instruments, rubbing alcohol, flammable 

fluids, or abrasive cleaners to remove tape or glue. These 

products can damage the surface of your refrigerator.

   Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside 

of your refrigerator before using it. See the cleaning instructions 

in the “Refrigerator Care” section.

Important information to know about glass shelves 
and covers:

Do not clean glass shelves or covers with warm water when 
they are cold. Shelves and covers may break if exposed to 
sudden temperature changes or impact, such as bumping. 
Tempered glass is designed to shatter into many small, 
pebble-size pieces. This is normal. Glass shelves and covers 
are heavy. Use both hands when removing them to avoid 
dropping.

Location Requirements

IMPORTANT:

 This appliances is intended to be used in 

household and similar applications such as:

 

Staff kitchen areas in shops, office and other working 

environments,

 

Farm houses and by clients in hotels, motels and other 

residential type environments,

 

Bed and breakfast type environments,

 

Catering and similar non-retail applications.

To ensure proper ventilation for your refrigerator, allow for a  

1/2

"

 (1.25 cm) space on each side and at the top. Allow for a  

1

"

 (2.54 cm) space behind the refrigerator. If your refrigerator has 

an ice maker, allow extra space at the back for the water line 

connections. When installing your refrigerator next to a fixed wall, 

leave a 3³⁄

4

"

 (9.5 cm) minimum space between the refrigerator 

and wall to allow the door to swing open.

NOTE: 

This refrigerator is intended for use in a location where 

the temperature ranges from a minimum of 55°F (13°C) to a 

maximum of 110°F (43°C). The preferred room temperature 

range for optimum performance, which reduces electricity usage 

and provides superior cooling, is between 60°F (15°C) and 90°F 

(32°C). It is recommended that you do not install the refrigerator 

near a heat source, such as an oven or radiator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as 

gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.

3³⁄

4

" (9.5 cm)

1/2" (1.25 cm)

Refrigerator Delivery

   A minimum door opening of 33" (838 mm) is required. If 

door opening is 36" (914 mm) or less, then removal of doors, 

drawer, and hinges is required.

   Cart the refrigerator from the side for all door openings.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for 
cleaning or service, be sure to cover the floor with 
cardboard or hardboard to avoid floor damage. Always pull 
the refrigerator straight out when moving it. Do not wiggle or 
“walk” the refrigerator when trying to move it, as floor 
damage could occur.

Содержание KRFC704FSS00







































Отзывы: