6
Display
When power is first supplied to the microwave oven, “0:00”
will appear in the display. If the “0:00” appears in the display at
any other time, a power failure has occurred. Reset the clock if
needed. See the “Clock” section.
When the microwave oven is in use, the display will show cook
time remaining. When the microwave oven is not in use, the
display will show the time of day (if the clock is set) or Timer
countdown (if the Timer is set).
Start
Start begins any function. If non-sensor cooking is interrupted by
opening the door, touching Start will resume the cycle.
NOTE:
To avoid unintentional operation of the microwave oven,
a cooking function cannot be started if the microwave oven
door has been closed for about 5 minutes. The word “door”
will appear in the display until the door is opened and closed.
Add 30 Seconds
Start Add 30 Sec automatically starts the microwave oven at
100% power for 30 seconds and it adds 30 seconds of cook
time with each additional touch of the keypad.
Time may be added to any manual cooking cycle in 30-second
increments, at the current power level, by touching Start Add 30
Sec during cooking.
NOTE:
To avoid unintentional operation of the microwave oven,
a cooking function cannot be started if the microwave oven
door has been closed for about 5 minutes. The word “door”
will appear in the display until the door is opened and closed.
Stop Cancel
The Stop Cancel keypad clears any incorrect command and
cancels any program during cooking. It will not erase the time
of day.
The microwave oven will also turn off when the door is opened.
Close the door and touch START to resume the cycle.
The Stop Cancel keypad is also used to lock and unlock the
control panel. See the “Control Lock” section.
Tones
Tones are audible signals that cannot be turned off.
One tone
■
Valid entry
■
Control Lock activated or deactivated
■
End of stage in multistage cooking
Three tones
■
End of Timer countdown
Five tones
■
End of cooking cycle
■
Reminder, repeating each minute after the end-of-cycle
and end-of-Timer tones
Clock
This is a standard 12-hour clock (1:00-12:59). The Clock cannot
be erased. If the Clock is not set, “0:00” will remain in the display
when the microwave oven is not in use.
To Set:
The microwave oven and Timer must be off.
1.
Touch CLOCK.
2.
Touch the number keypads to enter the correct time of day.
3.
Touch CLOCK.
Timer
The Timer can be set in minutes and seconds, up to 99 minutes
99 seconds, and counts down the set time.
NOTE:
The Timer does not start or stop the microwave oven.
Cook functions may be used while the Timer is counting down.
When the cook function is active in the display, touch TIMER to
see the Timer countdown for about 5 seconds.
To Set:
1.
Touch TIMER.
2.
Touch the number keypads to enter desired time.
3.
Touch START.
When the set time ends, “End” will appear in the display and
the end-of-Timer tones will sound.
4.
Touch STOP CANCEL while the Timer is active in the display
to cancel the Timer.
Language
The default display language is English, but it may be set to
French. Two display messages are affected: “End” (English) or
“Fin” (French) and “door” (English) or “PrtE” (“porte” - French).
To Set Language to French:
With the microwave oven door
open, touch and hold the number
1
keypad for about 3 seconds,
until a tone sounds. Repeat to change back to English. The
language remains set after a power failure.
Weight Entry Mode
The default weight entry mode for Defrost is imperial (pounds)
but may be set to metric (grams). This setting does not affect
any other program besides Defrost. See the “Defrost” section.
To Set Weight Entry to Metric:
With the microwave oven door
open, touch and hold the number
0
keypad for about 3 seconds,
until a tone sounds. Repeat to change back to imperial. The
mode remains set after a power failure.
Control Lock
The Control Lock disables the control panel keypads to avoid
unintended use of the microwave oven.
To Lock/Unlock Control:
The microwave oven must be off.
Touch and hold STOP CANCEL for about 3 seconds, until the
tone sounds and the Control Lock icon appears in the display.
Repeat to unlock.
If any keypad is touched while the control is locked, there will
be no response from the control.
