background image

7

INSTALLATION INSTRUCTIONS

Prepare Built-In Oven

1.

Decide on the final location for the oven. Avoid drilling or 
cutting into house wiring during installation. 

2.

To avoid floor damage, set the oven onto cardboard prior to 
installation. Do not use handle or any portion of the front 
frame for lifting.

3.

Remove the shipping materials and tape from the oven. 
Remember to keep the corner posts and other materials that 
may be needed for installation.

4.

Remove the hardware package from inside the bag 
containing literature.

5.

Remove and set aside racks and other parts from inside the 
oven.

6.

Move oven and cardboard close to the oven’s final location.

Remove Oven Door(s)

IMPORTANT:

 Use two hands to remove oven door. For double 

ovens, repeat the process for each door.

1.

Prior to removing the oven door, prepare a surface where you 
will place it. This surface should be flat and covered with a 
soft blanket, or use the corner posts from your packaging 
material.

2.

Open the oven door.

3.

Locate the oven door hinge locks in both corners of the oven 
door, and then rotate the hinge locks toward the oven door to 
the unlocked position. If the door hinge lock is not rotated 
fully (see illustration B), the door will not remove properly.

4.

Partially close the door to engage the door latch locks. The 
door will stop at this point.

5.

Using two hands, grasp the edges of the oven door. Lift and 
pull the oven door toward you and remove. You may need to 
gently shift door from side to side as you pull. 

6.

Set the oven door(s) aside on the prepared covered work 
surface, with the oven door resting on its handle.

7.

To continue with the oven installation, go to the “Positioning 
Oven Feet for Multiple Cabinet Cutout Heights” section.

Replace Oven Door(s)

1.

Using two hands, grasp side edges of door at the midpoint. 
Face the oven cavity.

2.

Locate the slots on each side of the oven cavity for the door 
hinge locks.

A. Oven door hinge lock in 

locked position

B. Oven door hinge lock in 

unlocked position

WARNING

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

A

B

A. Slot in the oven cavity for door hinge lock

A

Содержание KEBS109E

















Отзывы: