Kitagawa TT200BE-01 Скачать руководство пользователя

Страница: 41 / 69

14. Tilting Axis Over Travel Stop Device (See Fig.13)

14-1. Tilting axis over travel stop device

1) Remove the cover on the motor case side.

2) The dog and the limit switch of emergency stop for the tilting axis stroke limit are contained into the

rotating axis motor case.

3) The limit switch A

③

detects dog A

①

of stroke limit on the horizontal table face position side.

4) The limit switch B

④

detects dog B

②

of stroke limit on the vertical table face position side.

5) The angle until the emergency stop mode is applied to the machine from the horizontal table face is

about 35

. The angle until the emergency stop mode is applied to the machine from the vertical

table face is about 20

The angle values of 35

or more from the horizontal table face and 20

or more from the vertical table face cannot be set.

The angle may be limited within a standard value in advance by

customer conditions or to prevent the interference with the jig, workpiece,

etc. In this case, it cannot be set more than the limited angle.

14-2. Adjusting methods of dog for vertical over-travel

1) When the customer will change position of dog A

①

according to the shape of workpiece and jig,

loosen hexagon socket head cap screw which fix the dog A

①

. Once remove the dog A

①

2) Rotate the tilting axis to the tilting angle to be set in the minus direction with the manual pulse

generator or the Manual axis feed key, checking that it does not interfere with the jig or workpiece.

3) After rotating the rotary table to the desired tilting angle, slightly tighten hexagon socket head cap

screws which fix the dog A

①

4) Slide the dog A

①

in the reverse direction clockwise (CW) before fixing until the over-travel alarm

lamp lights. Tighten hexagon socket head cap screw that loosened slightly.

5) After fixing the dog A

①

, rotate the tilting axis again with the manual pulse generator or the Manual

axis feed key and check that the tilting axis stops at the desired tilting angle position and alarm lamp

lights.

6) After adjusting, mount the side cover of motor case on the rotating axis side.

When mounting the cover, coat the cover with liquid packing (liquid

gasket 1216 made by THREE BOND) evenly.

CAUTION

Содержание TT200BE-01






































































Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды

Kitagawa TT200BE-01, Инструкция по эксплуатации

Результаты поиска

Содержание TT200BE-01

Отзывы:

Похожие инструкции для TT200BE-01

Бренды по названию

Популярные бренды