manualshive.com logo in svg

Kirby Morgan M-48 SuperMask, Руководство пользователя

Поделиться
Скачать
Kirby Morgan M-48 SuperMask Скачать руководство пользователя страница 18

Pre-Dive

18

 

© MMXXI Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 210902001

B

 

WARNING

Not all second stage regulators can be properly mounted in 

the SCUBA pod. The size of the mouthpiece mounting tube 

and the placement and size of the exhaust tee can affect 

the mounting and proper functioning of the mouthpiece 

and folding action on the pod bellow. Use of a regulator 

that does not conform to the above stated requirements 

can result in drowning.

NOTE

Some divers may find the mouthpiece as supplied, to be too 
long. It is possible to trim the mouthpiece to a shorter length. 
Using scissors carefully shorten the mouthpiece at the trim edge 
notch as illustrated in Figure 1.

TRIM NOTCH

TRIM NOTCH

Figure 1 the M-48 mouthpiece

B

 

WARNING

Only the KMDSI mouthpiece P/N 810-022L will function 

correctly in your SCUBA pod. Do not attempt to use any 

other manufacturer’s mouthpiece. Doing so could result 

in death by drowning

Содержание M-48 SuperMask

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды