TSL20plus INCLUDED PARTS
Controller
OBD
Harness
Harness Length: 1 meter
NOTE:
The RED & WHT 2-pin connectors, as well as the connector on the back side near the
DIP switch block, are not used. Please do not connect anything to them.
PRODUCT WARRANTY CLAIM
TSL20plus
TOYOTA Auto Lock System
1 YEAR
(validated only by dealer and/or dated proof of purchase)
Year: , Month: , Day:
Name:
Address:
Phone:
Email:
Name:
Address:
Phone:
Website:
Approval Stamp
Manufacturer
:
Contact TEL
:
KIRAMEK, Inc.
9-183-1 Itayama-cho,
Handa-shi, Aichi-Ken 475-0936 JAPAN
+81-569-20-5585
( )
Operating Hours (
ex. Sat./Sun./Holidays
):
10:00AM ~ NOON, 1:00PM ~ 4:00PM
PRODUCT DESC.:
Warranty Period:
Date of Purchase*:
Customer Info.*:
* Please fill in these marked sections above completely.
NOTE
: Warranty Claims not accepted without valid
Approval Stamp and/or dated proof of purchase.
Seller Info.*:
MODEL:
1
2
3
4
5
6
AQUA
(Prius C*)
[NHP10]
AURION
(Camry*) [NZT260, ZRT26#] (Oct.2014 & later)
AURIS
[E18#H]
Corolla Axio
[NZE16#G]
Corolla Fielder
[E16#G]
ESQUIRE
[R8#, including hybrids]
iQ
[#GJ10]
LAND CRUISER PRADO
[J15#W]
NOAH
[R8#, including hybrids]
PORTE
[P141#]
PREMIO
[NZT260, ZRT26#] (Oct.2014 &later)
PRIUS
[ZVW30]
PRIUS-PHV
[ZVW3#]
PRIUSα
[ZVW4#]
RACTIS
[NSP120]
SIENTA
[P17#G]
SPADE
[P14#]
VITZ
[KSP130, NCP131] ***
VOXY
[R8#, including hybrids]
WISH
[ZGE2#G, ZGE2#W]
*
Car name outside Japan. TSL20 should work if these cars were made in Japan, but we have not confirmed compatibility.
*** Vitz (Yaris) cars manufactured June 2015 or later which have "Toyota Safety Sense C" are NOT compatible.
AURION
(Camry*) [NZT260, ZRT26#] (to Sep.2014)
PREMIO
[NZT260, ZRT26#] (to Sep.2014)
AURIS
[NZE15#H, ZRE15#H]
BLADE
[AZE15#H, GRE156H]
Corolla AXIO
[NZE14#]
Corolla Fielder
[E14#G]
Corolla RUMION
(Rukus*) [NZE151N, ZRE15#N]
IST
[NCP11#, ZSP110]
LAND CRUISER
[URJ202W]
MARK X ZiO
[ANA1#, GGA10]
NOAH
[ZRR7#G, ZRR7#W]
RACTIS
[NCP10#, SCP100]
VOXY
[ZRR7#G, ZRR7#W]
VITZ
(Yaris*) [NCP9#, SCP90, KSP90]
RAV4
[ACA3#W]
VANGUARD
[ACA33W, GSA33W]
BELTA
(Vios*) [KSP92, SCP92, NCP96]
Corolla AXIO
[ZRE14#]
FAMILY
1
2
3
4
5
6
1
ON
2
3
4
5
6
1
ON
2
3
4
5
6
1
ON ON
2
3
4
5
6
1
ON
2
3
4
5
6
1
ON ON
2
3
4
5
6
DIP SWITCHES
Find your car in the table below and adjust the
DIP switches accordingly.
The location of the DIP switches is shown in the
diagram at right.
VEHICLE SELECTION
1
3-STEP INSTALLATION
&RQQHFWWKH76/S·V2%'SOXJWRWKHFDU·V2%'SOXJ
2
Set vehicle compatibility DIP switch to match your car.
Use DIP SW#6 to confirm CAN signal compatibility.
Refer to “
VEHICLE SELECTION
” below.
Refer to “
OBD CONNECTION
” at right.
Refer to “
VEHICLE CONFIRMATION
” at bottom right.
1
3
OBD plug: choosing which side wires exit
&RQQHFWWRWKHFDU·V2%'DVVKRZQDERYH
You can choose which
side the wires exit.
TSL20p WIRE HARNESS
OBD PIN-OUTS
Color
Description
+12V
GND
CAN-HI
CAN-LO
RED
BLK
BRN
BRN/RED
pin16
pin14
CAN-LO
+12V
GROUND CAN-HI
pin6
pin4
OBD CONNECTION
2
9
1
9
1
If you already used the
included wire-tie, you will
need to remove it so you
can slide off the OBD cap.
NOTE:
When finished, secure
the wires to the tab on the
cap using a small wire-tie.
Slide off the
cap as shown.
Pull wires to the opposite
side and put cap on
as shown.
9
1
OPTIONAL
PARTS
0.65~0.8mm
PosiTap 4-pack
MRSP
¥
Compatible Wire:
Screw off
both caps.
Insert car wire into
Slot of cap. Screw
body onto cap.
Strip off 10mm of
insulation. Insert
through cap.
Insert wire first
into body. Screw
on cap tightly.
PosiTap
body
0.65~0.8mm, Car’s OBD wire
TSL20 wire
Slot
USING POSI-T
APS
Once you have completed all 3 Steps correctly, you simply need to
hide the TSL20p controller away from view and ensure you mount it
so it does not interfere with the foot pedals or the car’s moving parts.
At that point, your installation is complete!
DIP Switch #6
must be used as shown below to enable the TSL20p to function on
the chosen car. (DIP Switches #1 ~ #5 should have been set for your car in Step-1.)
NOTE:
When the above steps are finished, you never need to do them again for
WKHVDPHFDUHYHQLI\RXGLVFRQQHFWWKH2%'SOXJFKDQJH\RXUFDU·VEDWWHU\HWF
But if you move the TSL20p to a different car, you need to match the DIP Switches to
that car and then repeat the above 3 steps.
1
ON
2
3
4
5
6
1
2
3
Turn on the Ignition.
Flip DIP SW #6 to ON.
6
Flip DIP SW #6 to OFF.
6
FINAL SETUP
3
LO
CK
A
CC ON
STA
RT
COMPATIBLE VEHICLES
DIP Setting
NOTE:
,I WKH YHKLFOH·V 2%' SOXJ LV DOUHDG\ EHLQJ XVHG RU LI WKHUH LV QR VSDFH WR
DWWDFKWKH76/S·V2%'SOXJ\RXFDQHLWKHUSXUFKDVHRXURSWLRQDO
OB-23
splitter cable, or you can purchase our Posi-Tap connector 4-pack (p/n
NT-4
:HGRQ·WUHFRPPHQGVROGHUHGFRQQHFWLRQV<RXZRXOGEHVXUSULVHG
to know how many badly soldered connections result in problems!
800
WD[QRWLQFOXGHG