KIP KIPFold 2000 Скачать руководство пользователя страница 4

Страница: 4 / 34

KIPFold 2000

User Guide

No part of this publication may be copied, reproduced or distributed in any form without express written permission

from KIP.



2012 KIP.

- 3 -

Main connection cable

Do not use different connector cables, other than supplied with the folder. When replacement

of the power supply cable is required because of damage or defect, contact your CE for

proper replacement of this power supply cable.

Mains connection

Do not use an extension cable to connect the machine.

This machine is not designed for connection to an IT power supply system. An IT power

system is voltage network in which the neutral wire is not connected to earth.

When the machine is connected through a wall-socket, place the machine near a wall-socket

that is easily accessible.

When the machine is connected through a fixed connection to the electricity grid, the

disconnect device in the fixed connection must be easily accessible.

The machine must be connected to an earth (grounded) outlet.

Measures to take in case of an accident

1. If an accident has occurred, the distributor who has been notified first must immediately

take emergency measures to provide relief to affected persons and to prevent further

damage.

2. If a report of a serious accident has been received from a customer, an onsite evaluation

must be carried out quickly by an authorized person.

3. To determine the cause of the accident, conditions and materials must be recorded

through direct on-site checks, in accordance with instructions.

4. For reports and measures concerning serious accidents, follow the regulations specified

by the distributor.

Disclaimer

These safeguards have been compiled to the best of our knowledge. They are intended as a compact guide to the safe

handling of the product. We reserve the right to revise specification data sheets, as new information becomes available.

It is the user´s responsibility to determine the suitability of this information for the adoption of safety precautions as

may be necessary. It is the user´s responsibility to ensure that the specification data sheets are the

latest ones issued. If and in so far as limitation of liability is permitted under the applicable laws, we do not accept

liability for any inaccuracy that may occur in this information.

Содержание KIPFold 2000



































Результаты поиска

Содержание KIPFold 2000

Отзывы:

Похожие инструкции для KIPFold 2000

Бренды по названию

Популярные бренды

KIP KIPFold 2000, Руководство пользователя

Результаты поиска

Содержание KIPFold 2000

Отзывы:

Похожие инструкции для KIPFold 2000

Бренды по названию

Популярные бренды