KIP 770K Скачать руководство пользователя страница 8

Страница: 8 / 69

Chapter 1 Before Use

1-2

1. 1 Installation Requirements

The following conditions are required for the installation of the equipment.

1. Power source should be rated as:

U.S.A: 120V +/-10%, 50/60Hz, 15A or higher

Europe: 220-240V +6% or -10%, 50/60Hz, 10A or higher

2. The equipment must be on a dedicated circuit.

3. The outlet must be near the equipment and easily accessible.

I Norge: Kan kobles til IT strøm distribusjonssystemer.

1. Make sure to connect this equipment to a properly grounded outlet.

2. The outlet shall be installed near the equipment and shall be easily accessible.

Site Environmental Conditions

Temperature Range : 10

C to 32

C / 50 F to 89.6 F

Humidity Range

: 15% to 85% RH. (NON CONDENSING)

Keep the printer away from water sources, boilers, humidifiers, refrigerators or

kerosene (oil) stove.

1. The installation site must not have any open flames, dust or ammonia gases.

2. The equipment must not be exposed to the air vents from heating/cooling systems.

3. The equipment should not be exposed to the direct sunlight. Please draw curtains to

block any sunlight.

When you open the printer (Upper Half), do not expose the Photoconductive Drum to

strong (intense) light as this will damage the Drum.

Ozone will be generated while this equipment is in use, although the quantity generated is

within all safe levels. (see certifications)

Ventilate the room, if so required.

Keep ample space around the equipment to ensure comfortable operation.

The floor must be level and the strength must be ample to sustain the weight of the equipment.

KIP 770

20cm/8” or larger

20cm/8” or larger with no option

10cm/4” or larger

(Front)

(Rear)

Содержание 770K






































































Результаты поиска

Содержание 770K

Отзывы:

Бренды по названию

Популярные бренды

KIP 770K, Руководство пользователя

Результаты поиска

Содержание 770K

Отзывы:

Бренды по названию

Популярные бренды