KIOUR VD1T, Быстрый старт

Страница: 3 / 3

3
17 tdo
Time delay in deactivating the compressor once the door opens and activate the door alarm . Once the door
closes, the compressor is activated and the alarm turns off.
0 99 0 min
DEFROST
18 dFr
Time between two successive defrost , where if dFr = 0 or the relay is in heating mode, defrost is
deactivated.
0 50 6 hours
19 dd2 Defrost duration (manual and automatic) 1 90 18 min
20 dE5
Defrost end temperature - room temperature - terminals sensor 5-6
The defrost shut-off temperature is the temperature of the room, regardless of whether we have connected
the heat exchanger sensor. Above this room temperature the automatic defrost stops.
Manual defrosting starts regardless of the room temperature and is of duration dd2.
In case of fault (LF1) of the room sensor, the end of defrost temperature is not checked and is completed
after the selected time dd2.
0 25.0 10.0 °C/°F
21 dY4
Display indication during defrost
0 = room temperature is displayed
1 to 40 minutes = “dFr” is displayed from 1 to 40 minutes from the initiation of defrost 0 99 20 min
22 dP3 Dripping time, where the compressor is OFF after defrost 0 10 0 min
23 tdH
Time delay in activating high temperature alarm "AHi" after defrost.
The "AHi" alarm is not activated during defrost.
0 99 0 min
SMART DEFROST (more details page 2)
24 dSE
Smart defrost function
0 = NO
1 = YES 0 1 0 -
25 dSb
Starts a defrost cycle at the start of the device
0 = NO
1 = YES 0 1 1 -
26 dS2 Minimum time between two consecutive smart defrosts 40 255 60 min
27 dS1 Time constants, the steadier the increase, the harder it is to start smart defrosting 1 20 3 min
28 dSt Temperature constant, the higher the constant, the harder it is to start smart defrosting 0.5 3.0 1.0 °C/°F
COMPRESSOR
29 CP2 Compressor’s minimum time OFF 0 4 3 min
30 CF3
Compressor’s operation in case of room’s sensor malfunction LF1 and in cooling mode, the compressor
operates as follows :
0 = 40% ΟΝ compressor (3 minutes ΟΝ, 4 minutes OFF) / 1 = ΟΝ constantly the compressor.
In heating mode with parallel sensor malfunction (LF1), the relay switches off.
0 1 0 -
RELAY
31 rHC Relay operation mode, where 0 = cooling / 1 = heating / 2 = heating with countdown based on timer Hod 0 2 0=cooling -
32 Ηοd Countdown timer when the relay is in heating mode with countdown, adjust also parameter rHC = 2 1 255 1 min
NETWORK - GENERAL SETTINGS
33 Add Device address on network 0 255 1 -
34 trE Response time of the device on network 5 100 40 msec
35 bAU Baud rate: 2 = 9600 - - 2=9600 -
36 Pro Cabinet’s program (factory settings) is displayed – no access - - 1 -
37 tPE Unique product number – no access - - 45 -
ALARM TABLE
1 LF1 Room sensor malfunction
2 LF2 Evaporator sensor malfunction
3 ΑLo Low room temperature
4 ΑHi High room temperature
5 dοr Open door alarm
6 EEr RAM error: re-enter the SPo (see Setting the device temperature - SET POINT previous page)
The alarms are automatically deactivated once the cause of the alarm disappears.
Made in Greece
.
The device is under two year’s guarantee. The guarantee is valid only if the manual instructions have been applied. The control and service of the device must be done by an authorized technician.
The guarantee covers only the replacement or the service of the device. KIOUR PC implements a Quality Management System according to EN ISO 9001:2015 Standard with registration number
01013192.
KIOUR preserves the right to adjust its products without further notice
392 Mesogeion Avenue Agia Paraskevi 153 41 Τ: 210 6533730 F: 210 6546331 info@kiour.com www.kiour.com
V1.0.151020