Kioti LK30 Скачать руководство пользователя страница 111

Страница: 111 / 128

PERIODIC SERVICE

LK30 / LK35

PERIODIC SERVICE

LK30 / LK35

SERVICE AS REqUIRED

BLEEDINg FUEL SYSTEm

AIR mUST BE REmOVED:

1. When the fuel filter or lines are re

moved.

2. When tank is completely empty.
3. After the tractor has not been used

for a long period of time.

Your tractor is equipped with a plug

under the clutch housing.
After you operate your tractor in the

rain, snow, or after washing the trac-

tor, water may get into the clutch

housing. If this happens, remove the

plug in the clutch housing and drain

water. Remember to reinstall the plug

to avoid serious damage to clutch.

DRAININg CLUTCH HOUSINg

WATER

BLEEDINg PROCEDURE IS AS FOL-

LOWS:

1. Bleed the system with the fuel cock

in the air bleeding position.

2. Start the engine and run for 30 sec-

onds and then stop the engine.

3. Rotate the fuel cock to the open

position.

Fuses protect the tractor electrical

system from potential damage.
A blown fuse indicates that there is an

overload or short somewhere in the

electrical system.
If any of the fuses should blow, cor-

rect the cause of the short and re-

place with a new fuse of the same

capacity.

REPLACINg FUSE

(1) Fuse Box

(1) Plug

(1) Fuel Cock

(A) Close

(B) Open

S41Oa36a

S41Oa37a

S41Oa38a

LK35-AU-10.indd 25

2010-01-20 오후 3:19:46

Содержание LK30

































































































































Результаты поиска

Содержание LK30

Отзывы:

Бренды по названию

Популярные бренды

Kioti LK30, Руководство пользователя

Результаты поиска

Содержание LK30

Отзывы:

Бренды по названию

Популярные бренды