KINNEY KT SERIES Скачать руководство пользователя страница 31

Страница: 31 / 54

Maintenance

Manual 1843 Rev C p/n 001843 0000

Recommended Oil

The oil recommended for KT pumps in most

applications is KV-100 oil. KV-100 is specially

formulated to provide peak lubrication even in

arduous conditions and provide high pumping

capacity at low pressures. They are also

formulated to resist rust and oxidation. These

properties further enhance the performance and

durability of Kinney KT pumps.

See Table 7-1

for a list of recommended oils by

service type. LT oil may be required where low

temperature starting or process contamination is

encountered. Kinlube 220 may be recommended

where a fire retardant fluid is required. Halocarbo

125 is an inert fluid recommended for oxygen

service and for highly corrosive applications. S500

is a synthetic vacuum oil, and may be used when

the pump is run at elevated temperatures to avoid

contamination, or in other applications where a

petroleum-based oil is undesirable.

SERVICE TYPE

RECOMMENDED OIL

ISO GRADE

Standard

KV100

100

Refrigeration

POE

Brake Fluid

UCON

Ammonia

POE

Oxygen

Fomblin or other PFPE

100

Radiator Fill

KV100

100

High Temp

S500

100

Table 7-1 – Recommended Oils by Service Type

FACTORY SERVICE AND REPAIR

With proper care, Kinney vacuum pumps and

systems will provide years of reliable service.

Should adjustments or parts replacement

eventually be needed, these can often be

performed locally as described in this book after

obtaining required parts. Personnel should have a

good background of mechanical experience and be

thoroughly familiar with the procedures outlined in

this manual.

For major repairs not covered in this manual,

contact the nearest Kinney Authorized Service

Center. Pump repair services are also available

at our factory in Springfield, MO, or through ou

international network of Authorized Service Centers.

Call (800) 825-6937 for the location nearest you for

more information. Units that are still under warranty

must be returned to the factory, freight prepaid,

for service. Please contact Customer Service or

visist us online for additional instructions on how to

receive a Return Authorization number.

Current regulations require Material Safety

Data Sheet to be completed and forwarded

to Kinney on any unit being returned for any

reason which has been handling or involved

with hazardous gases or materials. This is

for the protection of the employees of Kinney

who are required to perform service on this

equipment. Failure to do so will result in

service delays.

Содержание KT SERIES























































Результаты поиска

Содержание KT SERIES

Отзывы:

KINNEY KT SERIES, Руководство оператора, Страница: 31 / 54

Результаты поиска

Содержание KT SERIES

Отзывы: