KINNEY KT-150 Скачать руководство пользователя страница 9

Страница: 9 / 22

Manual 1872 Rev B 001872 0000

KT-300 FILTER SYSTEM KIT COMPONENTS

FLOW

KT300 FILTER SYSTEM

KIT COMPONENTS

FIGURE 1

WARNINGS:

1. Ensure check valve is installed correctly with respect to flow. Incorrectly installed check valve can result in

pump failure and require total rebuild.

2. Hot oil can cause severe burns. Never remove filter while pump is running.

3. Do not use Teflon tape. This may void warranty.

NOTES:

1. Use only genuine Tuthill Replacement Oil Filter (part # 058379 0000). Contact your local Tuthill distributor or

email [email protected] to reorder replacement oil filters.

2. When starting KT Pump the green/red gage (#14 FIGURE 2) needle may be in the red until the oil is above 140

F, this is normal. If gage needle is in the red when temperature is above 140 F, replace filter.

INSTRUCTIONS:

***ENSURE YOU HAVE RECIEVED ALL PARTS INCLUDED IN PARTS LIST***

1. Lockout/Tagout machine. Use caution as oil & surfaces may be hot. Allow pump to cool to at least 100 F before

proceeding to drain oil.

2. Remove all existing oil plumbing except for the oil pump.

3. Ensure remaining plumbing ports are free of debris.

4. Remove the two bolts in the separator housing where the bracket will be mounted (refer to FIGURE 2). These

bolts will not be reused.

5. Loosely attach filter housing/bracket assembly using bolts and washers (#20 & #21 FIGURE 2).

6. Install kit plumbing as shown in FIGURE 2 starting with #1 using the Loctite 567 on all NPT parts. Tighten NPT fittings

but leave tube fittings loose until assembled. Tubes may be shortened/cut using a standard tube cutter. Ensure

check valve is orientated correctly with flow.

7. Once all plumbing is completely installed, tighten remaining tube fittings.

8. Refill oil per operators manual.

LOCTITE 567

OR EQUIVALENT

Figure 2-1 – KT-300 Filter Kit

(Retrofit Installation Only)

Содержание KT-150























Результаты поиска

Содержание KT-150

Отзывы:

Похожие инструкции для KT-150

Бренды по названию

Популярные бренды

KINNEY KT-150, Руководство оператора

Результаты поиска

Содержание KT-150

Отзывы:

Похожие инструкции для KT-150

Бренды по названию

Популярные бренды