Kingtel KT52IP Скачать руководство пользователя

Страница: 41 / 81

Field Name

Explanation

Choose the sip line to configured (SIP 1 – SIP2). Click the dropdown arrow to select the line.
Status

Shows registration status. Will show “Registered” if registered
or “Unapplied” if not registered.

Server Address

SIP server IP address or URI.

Server Port

SIP server port. Default is 5060.

Authentication User

SIP account name (Login ID).

Authentication Password

SIP registration password.

SIP User

Phone number assigned by VoIP service provider. Phone will not
register if there is no phone number configured.

Display Name

Set the display name. This name is shown on Caller ID.

Enable Registration

Check to submit registration information.

Domain Realm

SIP Domain if different than the SIP Registrar Server.

Proxy Server Address

SIP proxy server IP address or URI

（

This is normally the same as

the SIP Registrar Server)

Proxy Server Port

SIP Proxy server port. Normally 5060.

Proxy User

SIP Proxy server account.

Proxy Password

SIP Proxy server password.

Backup Server Address

Backup SIP Server Address or URI (This server will be used if the
primary server is unavailable)

Backup Server Port

Backup SIP Server Port

Server Name

Name of SIP Backup server

Codecs Settings

Click on the desired codec to select it. Then use the vol-/vol+ keys to move to the Enabled or
Disabled List. Use the Up/Down arrow to change the priority of enabled codecs.

Advanced SIP Settings

Forward Type

There are 3 call forwarding modes plus Disabled.
Disabled

：

No call forwarding – Default mode

Busy

：

If the phone is busy, incoming calls will be forwarded.

No answer

：

If there is no answer, incoming calls will be forwarded

after a specified time.
Always

：

All incoming calls will be forwarded.

Forward Number

Number to which calls are to be forwarded.

No Ans. Fwd Wait Time

Used in conjunction with Call Forward No Answer. Wait time in
seconds before call is forwarded.

Transfer Timeout

Time interval between sending “bye” message and hanging up
after the phone transfers a call.

Enable Hotline

Activate Hot Line feature. Automatically call a number by going

Содержание KT52IP


















































































Результаты поиска

Содержание KT52IP

Отзывы:

Похожие инструкции для KT52IP

Бренды по названию

Популярные бренды

Kingtel KT52IP, Руководство пользователя

Результаты поиска

Содержание KT52IP

Отзывы:

Похожие инструкции для KT52IP

Бренды по названию

Популярные бренды