manualshive.com logo in svg

Kingston Technology KTM609, Руководство по установке

Поделиться
Скачать
Kingston Technology KTM609 Скачать руководство пользователя страница 16

Installing the SIMM Modules

11

KTM-609/16 Installation Guide - Rev. D1

Kingston Technology Corporation

1. Install the highest capacity SIMM in socket P1 on your KTM-609/16 board.

Note that the SIMM plugs into the socket at an angle.

2. Carefully push the SIMM into the socket until it is firmly seated. Then push the

SIMM gently toward the memory board until the flanges shown in Figure 4
snap over either end of the module.

Figure 4  Installing the SIMM Modules

3. If you have another SIMM to install, plug the next highest capacity SIMM in

socket P2 on the KTM-609/16 board.  Use the same technique you used to
install the first.

4. If you have a third SIMM to install, plug the next highest capacity SIMM in

socket P3 on the KTM-609/16 board.

5. And if you have a fourth SIMM to install, plug it into socket P4 on the KTM-

609/16 board.  It should be the lowest capacity SIMM of all.

Now you are ready to install the KTM-609/16 board into your PS/2 computer.
Continue with the installation.

Содержание KTM609














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды