Combined or separate antenna option
When using a combination VHF/UHF antenna,
make sure the link is on (DEFAULT) and the
left hand input is used. For separate UHF and
VHF antennas, remove link and use the
left hand input for UHF, the middle
input for VHF. As shown in Fig.5.
Power through option
(MHU model only)
The MHU models have the ability to pass power
through to another amplifi er in line. To pass
power connect link to jumper labelled
power/pass. As shown in Fig.5.
Separate UHF and VHF inputs
Combination VHF/UHF input
Power Pass
COMBINED
LINK
PSK06F/08F
KPS06F/08F
PSK06/08
KPS06/08
POWER SUPPLY OPTIONS
4
Frequency range
VHF: 174–230 MHz
UHF: 520–694 MHz
Gain control range
43 dB models
VHF: Tilt control 16 – 12 dB
UHF: 10 dB
Max gain
43 dB models
VHF: 27–35 dB (W models only)
VHF: -2 dB (U models)
UHF: 43 dB
Supply voltage
PSK08/F
KPS08/F
PSK06/F
KPS06/F
Output fi gure
108 dB
DIN45004B @ (-60 dB IMR)
MHW43FS only
Pager fi lter
-25 dB @ 148 MHz and
158 MHz
Noise fi gure
VHF: < 3 dB
UHF: < 2.5 dB
FM fi lter
-25 dB @ 88–108 MHz
Band 1 fi lter
-30 dB @ 44 MHz
SPECIFICATIONS
Bare back cable with a cable
stripper or Stanley knife.
Slide on F connector and
crimp or use a twist on
connector.
The sheilded housing can pivot
to easily access connectors.
The lid can be inserted into the plastic
outer cover whilst installing.
Please see diagrams below for installation tips.
TECHNICAL ADVICE
1.
Check
there is no earth braid touching the
centre conductor on the coaxial cable.
2.
Is there more than one outlet?
Check
the splitter box, the power supply must be
connected to the coaxial outlet that feeds the
AC/DC leg of the splitter box to pass power
to the head unit. (Check if LED is on in the
amplifi er).
3.
Is there now too much signal causing
an overload effect?
Try turning down the
gain controls on the masthead unit, or select a
lower gain amplifi er.
4.
There is a white line moving through the
picture:
Try a PSK06 14 V DC power supply.
INSTALLATION
The Kingray Edge series of amplifi ers have
several built-in fi lters for interference rejection.
The inclusion of low band and LTE fi ltering (for
future 4G services) in this series provides a
future-proof solution.
The MHW version include fi lters for amateur
radio and pager frequencies as well as
a switchable FM radio fi lter.
FM fi lter (MHW versions only)
To eliminate FM radio interference; make sure
both jumper links are on the ‘FM trap IN’
(DEFAULT).
To amplify FM radio signals, set both jumper links
to ‘FM trap OUT’. As shown in Fig.1.
MHW43FS
MHU43FS
kingray.net.au
TV SET
PLUG INTO
WALL PLATE
SHORT CIRCUIT
PROTECTED
2M CABLE
17.5 V AC OR 14 V DC
MASTHEAD AMPLIFIER
PSK06F
INPUT
14 VOL
T DC
TV SET
PLUG INTO
WALL PLATE
17.5 V AC OR 14 V DC
MASTHEAD AMPLIFIER
SHORT CIRCUIT
PROTECTED
F
TO
F
MALE
ADAPTOR
2M CABLE
3
OUT
IN
OUT
IN
MHW43FS
MHU43FS
kingray.net.au
Fig 1
2
OUT
OUT
IN
FM TRAP
IN
47962-1_MHW-U43FS_IM.indd 4-6
16/10/14 4:28 PM