Kingfisher KI 9600 Series Скачать руководство пользователя страница 33

Страница: 33 / 52

KI 9000 UM-14

CALIBRATION AND MAINTENANCE

Light Source Calibration
The emitter power level can be re-calibrated, and the current checked.
Required are reference power meter with appropriate calibrated

wavelengths, single mode and multimode test leads, an anti-tamper

label. Check the calibration certificates on your reference equipment

to ensure current validity.
CAUTION! Use of controls or adjustments or performance of

procedures other than those specified herein may result in hazardous

radiation exposure.
Calibrate the source at the selected wavelengths as follows:

•

Inserting the

2.54 mm (0.1”) pitch programming shunt across

pins will put the instrument into calibration mode. It will

display ‘CAL’.

•

Press [



] to set the wavelength to be calibrated. Measure

light source power using the reference meter.

•

Press [



] to display DAC values from 0 to 1023 and

emitter current.

•

Set the emitter power to the required level by pressing

[MOD] to reduce and [LEVEL] to increase output.

•

Press [



] to save new value and to exit.

•

To return to factory default setting, press [



•

Repeat the above process for any additional wavelengths if

required.

Opening the Instrument:

CAUTION!

•

Do not open unless warranty has expired and you are

authorised to do so. Opening the unit will invalidate any

warranty claim.

•

This unit contains static sensitive devices. Anti-static

handling procedures should be observed at all times when

handling internal circuits.

•

There are no internal user adjustments. All calibration is

performed without opening the instrument. The optical

sensor / connector assembly is not user serviceable.

Procedure:

•

Open battery compartment and remove the batteries. Pull

open the optical connector cover.

•

Place the instrument face down on a soft mat, remove belt

clip and undo the screws in the rear housing. The instrument

can now be gently pulled apart.

•

Further disassembly from this stage should be easily

apparent to a technician.

•

Re-assembly is the reverse of the previous procedure.

Содержание KI 9600 Series





















































Результаты поиска

Содержание KI 9600 Series

Отзывы:

Похожие инструкции для KI 9600 Series

Бренды по названию

Популярные бренды

Kingfisher KI 9600 Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание KI 9600 Series

Отзывы:

Похожие инструкции для KI 9600 Series

Бренды по названию

Популярные бренды