background image

WARRANTY INFORMATION

2-YEAR 

 

LIMITED WARRANTY  

FOR THIS 20” PLANER

KING CANADA TOOLS

 

OFFERS A 2-YEAR LIMITED WARRANTY  

FOR COMMERCIAL USE.

PROOF OF PURCHASE 

Please keep your dated proof of purchase for warranty and servicing purposes. 

 

REPLACEMENT PARTS 

Replacement parts for this product are available at our authorized King Canada service centers across Canada. Please use the 10 digit 
part numbers listed in this manual for all part orders where applicable. 
 

PARTS DIAGRAM & PARTS LISTS

 

Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list. 
 

LIMITED TOOL WARRANTY 

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the 
original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from 
defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence 
or accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be 
liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.  
 
To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an                 
authorized King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our 
authorized service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if 
any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the            
warranty period. 
 

NOTE TO USER

 

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice. 
 
 
 
 
 

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4 

 

www.kingcanada.com

Содержание KC-525FX














Отзывы: