background image

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

REPLACEMENT PARTS

Replacement parts for this product are available at our authorized King Canada service centres across Canada. Please use the 10 digit

part numbers listed in this manual for all part orders where applicable.

LIMITED TOOL WARRANTY

King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the

original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from

defects in materials. warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence

or accidents, repairs done by an unauthorized service centre, alterations and lack of maintenance. King Canada shall in no event be

liable for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products. 

To  take  advantage  of  this  limited  warranty,  return  the  product  at  your  expense  together  with  your  dated  proof  of  purchase  to  an

authorized King Canada service centre. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our

authorized service centres. In cooperation with our authorized service centre, King Canada will either repair or replace the product if

any  part  or  parts  covered  under  this  warranty  which  examination  proves  to  be  defective  in  workmanship  or  material  during  the

warranty period.

NOTE TO USER

This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.

KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4

www.kingcanada.com

wARRANTY INFORMATION

2-YEAR 

LIMITED WARRANTY 

FOR THIS METAL CUTTING BANDSAW

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED WARRANTY 

INTENDED FOR NON COMMERCIAL USE

WARNING!

THIS MACHINE IS FOR METAL CUTTING ONLY!

IT IS NOT APPROVED FOR CUTTING WOOD. KING CANADA ACCEPTS NO RESPONSIBILITY FOR ANY

MACHINE WHEN USED FOR CUTTING WOOD AND WILL VOID THE ABOVE WARRANTY.

Содержание KC-129C












Отзывы: