King Canada CONNECT 1 8035LK-BC Скачать руководство пользователя страница 4

LITHIUM-ION BATTERY &  

CHARGER INFORMATION

WARNING

: The warnings, cautions, and instructions discussed in this instruction manual 

cannot cover all possible conditions and situations that may occur. It must be understood 
by the operator that common sense and caution are factors which cannot be built into this 
product, but must be supplied by the operator. Do not plug in charger or install battery into 
saw until you have read and understood this instruction manual.  
 

Available batteries and charger for this 20V max Li-ion for Angle Grinder: 

• 1.5 Ah 20V max Lithium-ion battery (Model K-020LBT) 
• 3.0 Ah 20V max Lithium-ion battery (Model K-023LBT-3) 
• 20V max Lithium-ion battery charger (Model K-020LCG) 
 
Charging any other battery may damage the charger and possibly cause serious injury. 
 

Battery and Charger Safety Precautions 

 

1) Do not store or carry battery

 in a way which metal objects could contact the exposed 

metal end of the battery. The battery could short-circuit causing a fire, personal injury 
and damage to the battery. 

2) Never attempt to open the battery

 for any reason. If battery housing has cracked,    

discontinue use immediately and do not try to recharge it. Dispose of battery. 

3) Never charge a wet battery

 or a battery that shows signs of corrosion. 

4) Do not use an extension cord

 with the charger, plug charger directly into a 120V AC 

receptacle. 

5) Do not use charger

 if power cord is damaged, replace damaged cord or charger. 

6) Do not charge battery

 when work area or the battery temperature is or below 0

0

C or 

above 45

0

C. 

7) Unplug charger

 when not in use. 

8) It is important to recycle

 or dispose of battery properly at your nearest battery     

recycling location. 

9) The contents of the battery is slightly acidic

, do not incinerate the battery, it can 

explode in a fire. 

10) A small leakage from the battery

 may occur under extreme usage, charging or      

temperature conditions. This does not indicate a battery failure. However, if the battery 
housing is cracked and leakage gets on your skin, follow these steps; 
-Wash with soap immediately. 
-Neutralize area with mild acid such as vinegar or lemon juice. 
-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes, then 
seek medical attention.

 

 

Lithium-ion Battery 

 
Lithium-ion batteries do not have a memory and do not require to be completely    
discharged periodically. After use, charge battery so that it is fully charged for the next time 
you use this tool. A fully charged battery will only loose about 2% of its charge per month 
during storage.

Содержание CONNECT 1 8035LK-BC









Отзывы: