OPERATION & MAINTENANCE
AUTOMATIC SUCTION SHUT-OFF AND EMPTYING LIQUID FROM TANK
This section relates to wet vacuuming operations. This vacuum is fitted with an automatic
suction shut-off float cup (A) Fig.14 which floats up when the liquid level increases in the tank,
it then stops the suction action when the tank has reached its maximum capacity of liquid. Make
sure the float cup is clean at all times.
The user will notice an increased motor speed, when this happens;
1) Turn off the vacuum immediately and unplug the power cord from the power source.
2) Remove the cover/motor assembly and lay it aside, being careful not to damage the filters
and empty the tank contents into a suitable waste disposal container by removing the drain
cap (B) Fig.14 found on the lower front of the tank.
3) The inside of the tank should be cleaned, also check the foam filter and clean it from the
inside out if necessary.
4) To continue vacuuming wet materials, reposition and secure the cover/motor assembly, plug
the power cord to a power source and proceed.
BLOWER FEATURE
This vacuum can be used as a powerful blower. To use the blower feature, disconnect the nut
end of the hose and reconnect it to the blower outlet as shown in Fig.15. Turn the vacuum On,
your vacuum is now a blower to clear work tables of debris, blow leaves etc...
STANDARD AND OPTIONAL ACCESSORIES
The following chart lists the standard accessories included and the available optional
accessories for this wet•dry vacuum. Please note that these accessories are not covered under
warranty and are available at your nearest King Canada distributor.
ON-BOARD ACCESSORY STORAGE
When the 10” floor sweep or crevice tool is not in use, it can be stored in the on-board storage
as shown in Fig.16.
MAINTAINING YOUR VACUUM AND ACCESSORIES
Warning! To reduce the risk of injury and electrical shock, unplug the power cord from
the power source. Airborn dust will be produced when cleaning, wear dust mask!
To maintain peak vacuum performance, the cartridge, foam and re-usable filters must be
cleaned often. When not in use, wrap the power cord around the power cord posts as shown in Fig.17.
Filter maintenance
- Clean the foam filter and re-usable filter by washing them inside out in a mild
soapy water and then rince with clean water. Clean the cartridge filter in a mild soapy water and
then rince with clean water. Allow these filters to dry completely before using.
General Maintenance and Inspection
- The inside of the tank, hose, extension wands and
accessories should be cleaned after every use, this cleaning should only be done outdoors with
the power cord disconnected from the power source. Check the condition of the power cord and
make sure it is not damaged. Also check the condition of the filters for tears and small holes. Do
not use filters with tears or small holes, replace with new filters.
TROUBLESHOOTING
Dust comes from the motor cover
-
Place/replace the dust bag if dust bag is missing or damaged.
Reduced efficiency/increased motor speed
-
Inlet is block or tank is full- Unblock inlet or empty tank through tank drain.
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram and
parts list.
FIGURE 13
FIGURE 14
FIGURE 16
FIGURE 15
FIGURE 17
Model
KVAC-1010
KVAC-1040
KVAC-1060
KVAC-1070
KVAC-1080
KVAC-1085
KVAC-1101
KVAC-1103
KVAC-1105
KVAC-1107
KVAC-1121
KVAC-1130
KVAC-1132
Description
30L Dust bags- 3pc. kit
Foam Filter- 1pc.
Re-usable Filter- 1pc.
Cartridge Filter- 1pc.
8ft. x 1-1/4” Flex Hose- 1pc.
8ft. x 2-1/2” Flex hose-5pc. kit
1-1/4” Round Brush- 1pc.
1-1/4” Gulper Tool- 1pc.
1-1/4” Crevice Tool- 1pc.
10” x 1-1/4” Floop Sweep- 1pc.
Caster Wheels- 4pc. kit
High Efficiency Cartridge Filter
30L High Efficiency Dust bags- 3pc. kit
Included/Optional
1pc. Included
1pc. Included
1pc. Included
1pc. Included
Optional
Optional
Optional
Optional
1pc. Included
1pc. Included
4pcs. Included
Optional
Optional
Usage
Dry Vacuuming Applications
Wet•Dry Vacuuming Applications
Wet•Dry Vacuuming Applications
Dry Vacuuming Applications
Hose with greater reach- extra 2ft
(Hose, 2pc. wand, floor sweep and crevice tool)
Upholstery and car interiors
General purpose
General purpose
General purpose-reversible attachment
Replacement kit
Drywall and fine dust applications
Drywall and fine dust applications
