kincrome KP15001, Быстрый старт

Страница: 5 / 10

5
GAS SOLDERING IRON KIT
Understanding The Supplied Accessories
The KP15001 Kincrome Gas Soldering Iron Kit is supplied with a number of accessories.
a. DEFLECTOR (14) is commonly used in heat shrink applications (Fig 1).
• To assemble the DEFLECTOR (14) to the gas soldering iron, first remove either the SOLDERING TIP (1), CHISEL
TIP (15), ANVIL TIP (16) or NEEDLE TIP (17) from the soldering iron by rotating the tip anti-clockwise.
Then you can slide the DEFLECTOR (14) sleeve over the SOLDERING TIP ASSEMBLY (3).
b. SOLDERING TIP (1) is a general size pointed soldering tip, suitable for soldering small wires (Fig 2).
• The SOLDERING TIP (1) can be removed from the SOLDERING TIP ASSEMBLY (3) by rotating the tip anti-clockwise or
installed onto the SOLDERING TIP ASSEMBLY (3) by rotating clockwise.
c.
CHISEL TIP (15) is a heavier/wider faced soldering tip, suitable for soldering medium to large wires (Fig 2).
• The CHISEL TIP (15) can be removed from the SOLDERING TIP ASSEMBLY (3) by rotating the tip anti-clockwise
or installed onto the SOLDERING TIP ASSEMBLY (3) by rotating clockwise.
d. ANVIL TIP (16) is a flat faced soldering tip, commonly used for spot/tack soldering (Fig 2).
• The ANVIL TIP (16) can be removed from the SOLDERING TIP ASSEMBLY (3) by rotating the tip anti-clockwise or installed
onto the SOLDERING TIP ASSEMBLY (3) by rotating clockwise.
e. NEEDLE TIP (17) is long narrow soldering tip, that is ideal for soldering where you don’t want excessive surface heat
generated or for soldering in recessed areas where a conventional standard tip cannot reach (Fig 2).
• The NEEDLE TIP (17) can be removed from the SOLDERING TIP ASSEMBLY (3) by rotating the tip anti-clockwise
or installed onto the SOLDERING TIP ASSEMBLY (3) by rotating clockwise.
f. TIP COOLING TRAY (18) is the round metal tray designed to hold any removed hot soldering tips & accessories , allowing
them to cool before placing them back into the cases EVA tray (Fig 3).
g. TIP CLEANING TRAY WITH SPONGE (19) is the round metal tray containing a sponge material. This accessory is designed
to assist the user in keeping the soldering tips clean during use (Fig 3).
WARNING!: Please take caution when cleaning the soldering tips as the sponge & water contained within the tip
can become hot during cleaning.
• With the sponge material sitting in the metal tray, add some clean water to the sponge until the water level
is just below the sponge height.
• While the soldering iron & tips are hot, gently swipe the tip face onto the damp sponge. Minimal pressure is
needed during this operation and the steam generated while the tip is applied to the sponge will quickly clean
any debris from the soldering tips.
h. FOLDING STAND (11) is located on the underside of the soldering iron and can be folded out allowing a hot soldering
iron to remain a safe distance away from your workspace (Fig 4).
• With the FOLDING STAND (11) extended, the soldering iron can be placed onto a surface during operation or once turned
OFF, the soldering iron can cool down without making contact with your workspace, ready to put back into the cases EVA tray.
LIGHTING AND OPERATION
WARNING!: Before each use, ensure that LOCKING NUT (5) and all related tips and accessories are securely
connected and tight.
Press and Hold Mode
a. Turn FLAME ADJUSTMENT KNOB (10) approximately halfway between (2) and (3) position, located below
the FOLDING STAND (11).
b. Press the LOCK OFF BUTTON (6) down and slide the IGNITER SWITCH (7) away from burner tip.
c. To turn OFF the KP15001, release IGNITER SWITCH (7) to extinguish KP15001.
(Fig 1) (Fig 2) (Fig 3)
(Fig 4)