Thank you for purchasing a Kincrome product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
Ensure the lamp is fully charged before initial use.
DO NOT turn the lamp on when it is being charged.
DO NOT shine directly into your, other person’s or
animal’s eyes.
DO NOT allow children to use the lamp.
DO NOT handle or move the lamp whilst it is being
charged.
DO NOT use the lamp if you suspect that the battery
or the lamp casing is damaged.
DO NOT leave battery in a discharged state, recharge
battery immediately. Before storage, fully recharge the
battery, subsequently recharge the battery at least
once every six months of non-use.
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR
CONNECTING LAMP TO THE POWER SUPPLY.
WARNING! It is the user’s responsibility to read,
understand and comply with the following electrical
instructions:
You must ensure the risk of electric shock is minimised
by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be
incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is
used with all electrical products, particularly portable
equipment which is plugged into an electrical supply
not protected by an RCCB.
You must also read and understand the following
instructions concerning electrical safety:
If in any doubt about electrical safety, contact a
qualified electrician.
1.2.1.
You must ensure that you:
Inspect the charger plug, cable and connector for
wear and damage to ensure items are safe before
connecting to the mains power supply. If worn or
damaged
DO NOT use.
Important: Check that the voltage marked on the
charger plug is the same as the lamp.
Uncoil the cable between charger and the lamp.
DO NOT pull the charger plug from the mains socket by
the lead.
WARNING! DO NOT use any other type of charger with
this product, other than the supplied mains or car
charger. Failure to observe this warning could result in
injury and or fire and will invalidate the warranty.
DO NOT try to take the charger plug apart.
DO NOT use the charger plug to charge or power any
other electrical item.
DO NOT get the charger wet, or use in wet, damp
conditions (for indoor use only).
1.3. BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
DO NOT attempt to open, disassemble, modify or
service the battery pack.
DO NOT crush, puncture, short external contacts or
dispose of in fire or water.
DO NOT expose to temperatures above 60°C (140°F).
Replace only with the battery pack designated for this
product.
Recycle or dispose of used battery as stipulated by local
regulation.
If the electrolyte in the cells gets on your skin,
thoroughly wash with soap and water. If it gets in your
eyes, rinse thoroughly with cool water and seek
immediate medical attention.
The super brilliant rechargeable K10206 SMD Pocket Worklight is a versatile compact professional quality worklight that fits com-
fortably in the palm of the hand, and can be stored and carried conveniently in a pocket.
With a two stage switch the worklight can be used in either High or Low power settings offering up to six hours of use before
charging is required.
The five SMD (Surface Mount Diode) LEDs are 150 Lumens in High mode, or 60 Lumens in Low mode, give off very little heat
and produce a wide, even arc of light.
The K10206 SMD Pocket Worklight incorporates a 180° Angle Stand, powerful magnet, 360° swivel hook and heavy duty pocket
clip allowing the user virtually endless mounting options for hands free work for most lighting conditions.
2. INTRODUCTION / SPECIFICATION
INSTRUCTION MANUAL FOR:
SMD LED POCKET WORK LIGHT
LITHIUM-ION
Part No: K10206
Part No: .......................................................................... K10206
Battery: ................................................LI-ion 3.7Vd.c. 1500mAh
LED Quantity: ..............................................................5 (x 0.5W)
Lumen Output: ....................................150lm (High) / 60lm(Low)
Operating Time: ......... 3hrs high brightness/6hrs low brightness
Charging Time: .....................................................................3hrs
