Thank you for purchasing a Kincrome product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
Ensure the lamp is fully charged before initial use.
DO NOT turn the lamp on when it is being charged.
DO NOT shine directly into your, other person’s or
animal’s eyes.
DO NOT allow children to use the lamp.
DO NOT handle or move the lamp whilst it is being
charged.
DO NOT use the lamp if you suspect that the battery
or the lamp casing is damaged.
DO NOT leave battery in a discharged state, recharge
battery immediately. Before storage, fully recharge the
battery, subsequently recharge the battery at least
once every six months of non-use.
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR
CONNECTING LAMP TO THE POWER SUPPLY.
WARNING! It is the user’s responsibility to read,
understand and comply with the following electrical
instructions:
You must ensure the risk of electric shock is minimised
by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be
incorporated in the main distribution board. We also
recommend that an RCD (Residual Current Device) is
used with all electrical products, particularly portable
equipment which is plugged into an electrical supply
not protected by an RCCB.
You must also read and understand the following
instructions concerning electrical safety:
If in any doubt about electrical safety, contact a
qualified electrician.
1.2.1.
You must ensure that you:
Inspect the charger plug, cable and connector for wear
and damage to ensure items are safe before connecting
to the mains power supply. If worn or damaged
DO NOT
use.
Important: Check that the voltage marked on the
charger plug is the same as the lamp.
Uncoil the cable between charger and the lamp.
DO NOT pull the charger plug from the mains socket by
the lead.
WARNING! DO NOT use any other type of charger with
this product, other than the supplied mains or car
charger. Failure to observe this warning could result in
injury and or fire and will invalidate the warranty.
DO NOT try to take the charger plug apart.
DO NOT use the charger plug to charge or power any
other electrical item.
DO NOT get the charger wet, or use in wet, damp
conditions (for indoor use only).
1.3. BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
DO NOT attempt to open, disassemble, modify or
service the battery pack.
DO NOT crush, puncture, short external contacts or
dispose of in fire or water.
DO NOT expose to temperatures above 60°C (140°F).
Replace only with the battery pack designated for this
product.
Recycle or dispose of used battery as stipulated by local
regulation.
If the electrolyte in the cells gets on your skin,
thoroughly wash with soap and water. If it gets in your
eyes, rinse thoroughly with cool water and seek
immediate medical attention.
Unique and innovative 360° swivel and tilt function enables the light source to be positioned in any direction. Each lamp houses
10 super bright SMD (Surface Mounted Diode) LEDs providing up to 400 lumens output with two selectable modes of brightness
and 120° spread of light, illuminating the whole work area. Includes an additional high power 3W LED in the end for use as a
directional torch. Features two swivel hooks and three rubber covered magnets, two on the rear and one on the end, which allow
hands free operation. High quality 2200mAh Lithium-ion battery for longer life, no memory effect and a much slower discharge
than traditional Ni-MH batteries. Supplied with mains and in car charger.
2. INTRODUCTION / SPECIFICATION
INSTRUCTION MANUAL FOR:
SMD LED INSPECTION LIGHT
LITHIUM-ION
BLACK
Part No: K10202B (BLACK)
Part No: ........................................................................ K10202B
Battery: ................................................Li-ion 3.7Vd.c. 2200mAh
LED Quantity: ......................................................................10+1
Lumen Output: .................................................................. 400lm
Top Torch .......................................................................3W LED
Minimum Length: ............................................................260mm
Maximum Length: ...........................................................280mm
Operating Time: ............................................. 3hrs high/6hrs low
Top Torch Operating Time: .................................................10hrs
Charging Time: .....................................................................4hrs
Ingress Protection Rating ....................................................IP54
