Kikusui PWX1500H Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 131

background image

4

PWX

When using this product, be sure to observe the “Safety
Precautions” in the Safety information manual.

When installing this product, be sure to observe the
“Precautions Concerning Installation Location” in the
Safety information manual. The following precautions
pertain only to this product.

• When installing this product, be sure to observe the tem-

perature and humidity ranges indicated below.

Operating temperature range: 0

°

C to +50

°

C

(32

°

F to 122

°

F)

Operating humidity range: 20 %rh to 85 %rh
(no condensation)

• When storing this product, be sure to observe the tempera-

ture and humidity ranges indicated below.

Storage temperature range: -10 °C to +60 °C
(14 °F to 140 °F)
Storage humidity range: 90 %rh or less (no condensation)

• In this manual, the PWX Series Regulated DC Power Sup-

ply is referred to as the “PWX Series” or “PWX.”

• The term “PC” is used to refer generally to both personal

computers and workstations.

• The screen captures used in this manual may differ from the

actual screens that appear on the PWX series. The screen
captures are merely examples.

• The following markings are used in this manual.

Indicates a potentially hazardous situation which, if
ignored, could result in death or serious injury.

Indicates a potentially hazardous situation which, if
ignored, may result in damage to the product or other
property.

Indicates information that you should know.

Explanation of terminology or operation principle.

Indicates a reference to detailed information.

Indicates reference to detailed information operation man-
ual.

CFxx:x

“CF” stands for a CONFIG parameter. The two digits after
CF indicate the CONFIG parameter number. The value
after the colon indicates the selected setting.

SHIFT+key name (blue characters below the keys)

Indicates an operation that requires you to press a key
indicated in blue characters (below the key) while holding
down the SHIFT key.

Indicates useful information.

Safety Precautions

Precautions Concerning

Installation Location

Notations Used in This Manual

WARNING

CAUTION

DESCRIPTION

See

Memo

«
...
2
3
4
5
6
...
»

Содержание PWX1500H




































































































































Отзывы:

Нет отзывов

Похожие инструкции для PWX1500H

Бренд: C&H Technologies Страницы: 24

Бренд: Ganz Страницы: 8

Бренд: Kärcher Страницы: 208

Бренд: Campbell Hausfeld Страницы: 32

Бренд: Würth Страницы: 8

Stellar PowerPlant 3

Бренд: PS Audio Страницы: 20

Бренд: X-Tronic Страницы: 12

Бренд: Parkside Страницы: 80

Бренд: On-Q Страницы: 2

Бренд: Cantek Страницы: 29

Бренд: Tripp Lite Страницы: 3

Бренд: LANCMAN Страницы: 32

Бренд: Ingersoll-Rand Страницы: 8

Бренд: SATA Страницы: 16

Бренд: Parkside Страницы: 43

Бренд: Sealey Страницы: 3

Бренд: Parkside Страницы: 184

BOSTITCH PROFESSIONAL QuietSharp Glow EPS11HC

Бренд: Stanley Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды