Kikusui PFX2532 Скачать руководство пользователя | Manualshive

Страница: 91 / 142

background image

PFX2532

91

6

V

o

lt /

T

h

er

mo

me

te

r Unit (

O

p

tio

n)

Connecting the DUT (Battery)

1

Check that the POWER switches of all connected devices are off.

2

Connect DUT cables to the positive and negative DUT terminals of the
PFX2532.

Run the cables out as horizontal as possible, and fix them in place with screws.

3

Connect the other end of the DUT cables to the DUT (battery). Connect DUT +
to the positive terminal and DUT - to the negative terminal.

4

Insert the assembled thermocouple and cell voltage sensing cable connectors
into the OP02-PFX input terminals.

5

Connect the other end of the cell voltage sensing cables to the DUT (battery).
Connect the positive cell voltage sensing terminal to the DUT (battery)
positive terminal and the negative cell voltage sensing terminal to the DUT
(battery) negative terminal.

6

Fix the other end (the end that is used to measure the temperature) of the
thermocouple to the DUT (battery).

Use tape, or another appropriate adhesive, to firmly fix the thermocouple to the DUT.

7

Insert the assembled sensing connector into the PFX2532 SENSING connector.

8

Connect or attach a voltage sensing cable and thermistor to the DUT
(battery).

WARNING

Risk of electric shock.

• Be sure to turn the PFX2532 POWER switch off before connecting OP02-PFX units to the

DUT (battery).

• After connecting the devices, connect the OP02-PFX to the DUT (battery). Connect the

OP02-PFX side first.

CAUTION

• Risk of incorrect voltage measurement or malfunction. Be sure to connect the cell voltage sensing

cable to both ends of the cell. (

• CC-CV, CP, and CP Pattern are controlled by the PFX2532 voltage sensing function. Be sure to

connect the PFX2532 voltage sensing cables to the DUT.

• Risk of damaging the DUT.

If you leave the cell voltage sensing cables connected to the DUT, the DUT will continue to
discharge a minute current. (the input impedance of cell voltage sensing is 10 MΩ).

• Risk of incorrect temperature measurements or thermometer malfunction. Do not connect the

thermocouple element wires (the conductive parts) to the positive and negative terminals of the
DUT (battery).

See

See

See

«
...
89
90
91
92
93
...
»

Содержание PFX2532















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PFX2532

Бренд: Vacon Страницы: 64

Бренд: Jedo Страницы: 26

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 14

Бренд: Hama Страницы: 8

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

Бренд: Neets Страницы: 12

Бренд: National Instruments Страницы: 24

Бренд: tau Страницы: 9

Бренд: tau Страницы: 8

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды