manualshive.com logo in svg

Kikusui BIM1000 Series, Руководство пользователя

Поделиться
Скачать
Kikusui BIM1000 Series Скачать руководство пользователя страница 85

BIM1000 Series

User’s Manual

85

Specifications | General specifications

General specifications

Item

BIM1030

BIM1100

Environment

Installation location

Indoors, 2000 m or less 

Spec guaranteed 
range

Temperature

18 °C to 28 °C (-4 °F to 158 °F)

Humidity

20 %rh to 80 %rh (no condensation)

Operating range

Temperature

0 °C to 40 °C (32 °F to +122 °F)

Humidity

20 %rh to 80 %rh (no condensation)

Storage range

Temperature

-10 °C to 60 °C (-4 °F to 158 °F)

Humidity

90 %rh or less (no condensation)

Power supply

Input voltage range

85 Vac to 264 Vac (100 Vac to 240 Vac)

Input frequency range

47 Hz to 63 Hz

Rated power

30 VA

Isolation voltage

±300 V max

±1000 V max

Insulation resistance (between AC LINE and chassis)

30 MΩ or more (500 Vdc)

Withstanding 
voltage

Between the AC LINE and the chassis 1500 Vac for 1 minute, 10 mA or less

Between all the measurement termi-
nals and the chassis

2000 Vdc for 1 minute, 1 mA or less

Between all the measurement termi-
nals and SIGNAL I/O

2000 Vdc for 1 minute, 1 mA or less

External dimensions

See 

p.86 

.

Weight

Approx. 3 kg (6.6 lbs)

Accessories

See 

p.2 

.

Electromagnetic compatibility (EMC)

*1

 

*2

*1.

Does not apply to specially ordered or modified products.

*2.

Limited to products that have a CE mark.

Complies with the requirements of the following directive and 
standards.
EMC Directive 2014/30/EU
EN 61326-1 (Class A

*3

)

EN 55011 (Class A*3, Group 1

*4

)

EN 61000-3-2
EN 61000-3-3

Applicable under the following conditions
The maximum length of all cabling and wiring connected to 
the product must be less than 2.5 m.
Shielded cables are used to connect to SIGNAL I/O.
TL01-BIM clip-type four-wire test leads are used.
Electrical discharges are applied only to the DUT.

*3.

This is a Class A instrument. This product is intended for use in an industrial environment. This product may cause 
interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce 
electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.

*4.

This is a Group 1 instrument. This product does not generate and/or use intentionally radio-frequency energy, in the form of 
electromagnetic radiation, inductive and/or capacitive coupling, for the treatment of material or inspection/analysis purpose.

Safety*1

Complies with the requirements of the following directive and 
standards.
Low Voltage Directive 2014/35/EU*2
EN 61010-1 (Class I

*5

, Pollution Degree 2

*6

)

EN 61010-2-030
EN 61010-031

*5.

This is a Class I instrument. Be sure to ground this product's protective conductor terminal. The safety of this product 
is guaranteed only when the product is properly grounded.

*6.

Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduction of dielectric strength or 
surface resistivity. Pollution Degree 2 assumes that only non-conductive pollution will occur except for an occasional 
temporary conductivity caused by condensation.

Содержание BIM1000 Series































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды