KidKraft F24035EX Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 40

KidKraft F24035EX Скачать руководство пользователя страница 16

Step 14 Swing Asy B

Step 3: Attach Swing End to Swing Beam

A:

Place (A32) SW Rail Block in the centre between (A1) CE SW Beam Back and (A2) CE SW Beam Front and

attach with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with lock washer, flat washer and t-nut). (fig. 3.1 & 3.2)

B:

Attach Swing Beam Assembly to the side of the Swing End Assembly with the overhang (fig. 3.3 & 3.4) using 1

(G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of Triangle Plate and 1 (GL8)

5/16 x 2” Hex Bolt (with 2 flat washers and lock nut) in the bottom hole of Triangle Plate. (fig. 3.3) Make sure

Swing End Assembly flares out at an angle.

Step 14 Swing Asy B

Step 14 Swing Asy B

100°

Fig. 3.1

Side with

Overhang

H8

A2

A1

Fig. 3.2

Fig. 3.3

Fig. 3.4

A32

G5

GL8

1 x

SW Rail Block 2 x 4 x 5-3/8”

A32

Hardware

Wood Parts

1 x

1/4 x 4-1/4” Hex Bolt

(1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

5/16 x 4-1/2” Hex Bolt

(5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

1 x

5/16 x 2” Hex Bolt

(5/16” flat washer x 2, 5/16” lock nut)

H8

G5

GL8

Hex Bolt Assembly

Lock

Washer

T-Nut

Flat

Washer

Hex

Bolt

16

«
...
14
15
16
17
18
...
»

Содержание F24035EX









































Отзывы:

Нет отзывов