KidKraft COZY ESCAPE PLAYHOUSE F29045 Скачать руководство пользователя | Manualshive

Страница: 1 / 81

background image

Table of Contents

Warnings and Safe Play Instructions  .  .  .  .  .  .  .  .  .  . pg . 2
Protective Surfacing Guidelines .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 3
Instructions for Proper Maintenance   .  .  .  .  .  .  .  .  . pg . 4
About Our Wood – Limited Warranty  .  .  .  .  .  .  .  .  . pg . 5
Keys to Assembly Success   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 6
Part ID   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 8-19
Step-By-Step Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .pg . 20
Installation of I .D ./Warning Plaque  .  .  .  .  .  .Final Step

Rev 05/08/2019

9409045

KidKraft, Inc.

4630 Olin Road

Dallas, Texas 75244 USA

[email protected]

[email protected]

1.800.933.0771

972.385.0100

For online parts replacement visit

https://parts.kidkraft.com/

KidKraft Netherlands BV

Olympisch Stadion 29

1076DE Amsterdam

The Netherlands

[email protected]

+31 20 305 8620 M-F from 09:00 to 17:30

(GMT+1)

For online parts replacement visit

https://parts.kidkraft.eu/

COZY ESCAPE PLAYHOUSE - F29045

INSTALLATION AND OPERATING INSTRUCTIONS

2 - 4 Hrs

FOR FORT

TWO PERSON

ASSEMBLY

2-4 Hrs

10 - 12 Hrs

FOR FORT & SWING

TWO PERSON

ASSEMBLY

10 - 12 Hrs

FOR FORT & SWING

1 - 2 Hrs

TUBE SLIDE

277cm

677cm

720cm

320cm

10’ 6”

7’ 25”

23’ 7.5”

20’ 1.7”

To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and

refer to these instructions often and give them to any future owner of this play set. Manufacturer

contact information provided below.

OBSTACLE FREE SAFETY ZONE - 23’ 7.5” x 20’1.7” (720 x 677 cm) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 56-5/16” (1.43m)
CAPACITY - 11 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs.

(49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as

multi-unit residences, schools, churches, nurseries, day cares or parks.
Warning. Only for domestic use.

For Outdoor Family

Domestic Use Only

WARNING

1
2
3
...
»

Содержание COZY ESCAPE PLAYHOUSE F29045


















































































Отзывы:

Нет отзывов

Похожие инструкции для COZY ESCAPE PLAYHOUSE F29045

Бренд: Varec Страницы: 74

Бренд: Campbell Страницы: 18

Бренд: Gardco Страницы: 17

Бренд: H&S Страницы: 42

Бренд: Aeroflex Страницы: 211

Бренд: ATD Tools Страницы: 7

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Бренд: SDE Lighting Страницы: 7

Бренд: DeLaval Страницы: 26

E-Boxx EV Simulator

Бренд: Walther Страницы: 12

Бренд: Forch Страницы: 36

EASY FLOW CATTLE ALLEY

Бренд: Arrowquip Страницы: 24

Бренд: ProLights Страницы: 36

SPEKTRA ZOOM/200W FRESNEL LED

Бренд: Gamma Страницы: 7

Бренд: XENUM Страницы: 8

Бренд: Graci-lite Страницы: 2

Бренд: Suzuki Страницы: 2

rescueME Series

Бренд: Ocean Signal Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды