Kicker V55 PWRA207 Скачать руководство пользователя страница 9

Page 9 of 10 

Symptom 

Possible Cause 

Solution 

No Subwoofer Output 

Fuse not installed in inline 

fuse holder on subwoofer 

and/or amp harness 

Install fuse(s) into fuse holder(s).  Refer to 

instructions for correct placement 

Low battery voltage 

Recharge the battery 

Negative battery cable not 

connected 

Reconnect negative battery cable 

Power wire connector not 

connected to body harness 

Connect power wire to body harness.  Check 

for loose connection 

Ground wire not grounded 

properly 

Check ground wire with voltmeter to insure it is 

a good ground 

Signal input connector not 

connected properly 

Connect signal wire of subwoofer harness to 

signal wire of amplifier harness or factory 

speaker wire depending on application.  

Check for loose connection 

Balance or fader controls not 

set to neutral position 

Set balance and fader control to center 

settings.  (only affects stand alone subwoofer 

kit) 

No low frequency 

information in music 

Test with several different songs 

Subwoofer harness not 

properly/completely 

connected to subwoofer. 

Securely fasten both of the connectors on the 

subwoofer harness to the subwoofer.  Check 

for loose connections. 

Radio not coming on 

Radio connector not 

properly/completely 

connected 

Check radio connector to insure it is 

completely seated 

Blown radio fuse 

Refer to owner's manual for radio fuse location 

and value 

Low battery voltage 

Recharge the battery 

Radio comes on, but no 
sound from any speakers 

Fuse not installed in inline 

fuse holder on amplifier 

harness 

Install fuse into fuse holder.  Refer to 

instructions for correct placement 

Radio connector not 

properly/completely 

connected 

Check radio connector to insure it is 

completely seated 

Ground wire not grounded 

properly 

Check ground wire with voltmeter to insure it is 

a good ground 

Low battery voltage 

Recharge the battery 

If you continue to experience problems after troubleshooting with this list, please contact KICKER Technical Support at 
(800) 256-0808 ext. 6009, or [email protected]

Содержание V55 PWRA207











Отзывы: