background image

11

English

Troubleshooting

If the KPB becomes frozen or stuck during algorithmic calculation, does not 
appear to be working, or gives an error code, check the obvious things first 
such as blown fuses, poor or incorrect wiring connections, incorrect setting 
of gain controls, etc.

No power? 

With a Volt Ohm Meter (VOM) check the following:  

Œ

+12 volt 

power terminal (should read +12V to +16V)  



Check for reversed power 

and ground connections  

Ž

Ground terminal, for proper conductivity.

Power on, no signal? 

Check the following:  

Œ

RCA connections  



Test 

audio source signal, either with a “known good” output device or other 
means.

Bluetooth device will not connect? 

On your mobile device:  

Œ

Turn 

Bluetooth off, then on again.  



Remove ‘KPB1/2 KICKER’ from the 

Bluetooth menu. Then pair again (see page 9).  

Ž

Move your mobile device 

closer to the speaker. Avoid obstacles that may block the wireless signal.



Perform a factory reset by pressing and holding the PLAY/PAUSE button

for 10 seconds.

No or low output?

  

Œ

Check the settings on the audio source.  



Check 

the RCA (or speaker input) and speaker output connections.

KPB frozen or stuck in operating procedure? 

Œ

Perform factory reset 

the KPB  



Cycle the power

Broadcast Mode will not engage?

  

  

Œ

Follow the instructions to enter 

Broadcast Mode on page 9.  



 Perform a factory reset on both primary 

and secondary KPBs.

CAUTION:

  When jump starting the vehicle, be sure that connections 

made with jumper cables are correct. Improper connections can result in 
blown fuses as well as the failure of other critical systems in the vehicle.

If you have more questions about the installation or operation of your new 
KICKER product, see the Authorized KICKER Dealer where you made your 
purchase. For more advice on installation, click on the SUPPORT tab on 
the KICKER homepage, 

www.KICKER.com

. Choose the TECHNICAL 

SUPPORT tab, choose the subject you are interested in, and then 
download or view the corresponding information. Please E-mail support@
KICKER.com or call Technical Services (405) 624-8583 for unanswered or 
specific questions.

Содержание PowerBar KPB1
















Отзывы: