Kicker 19417166 Скачать руководство пользователя страница 12

12

 

 

Troubleshooting the Kicker Integrated Systems 

 

If you experience a problem once the subwoofer or amplifier are installed use this guide to locate the trouble. 

 

The radio is working, but the Subwoofer is not working: 

  Check the battery voltage to make sure it is not discharged below 11 volts. 

  Check the negative battery cable to see if it has been securely tightened back on the battery. 

  Check the inline fuse located near the battery to make sure it is plugged in completely, and not blown. 

  Check the 12 volt power connector near the firewall to make sure it is plugged in securely. 

  Check the inline connectors near the subwoofer enclosure to make sure they are plugged securely. 

  Check the ground wire connection to make sure it is tightly secured to the proper ground in the vehicle. 

  Check the audio input signal connection to make sure it is secure and connected to the proper wiring. 

  Test with different music in case there is no low frequency audio in the initial sound check. 

 

 

There is a problem with the multi-channel stereo amplifier: 

  Check the battery voltage to make sure it is not discharged below 11 volts.

 

  Check the negative battery cable to see if it has been securely tightened back on the battery.

 

  Check the inline fuse located near the battery to see if it is plugged in completely and not blown.

 

  Check the multi-pin connectors at the back of the radio and at the amplifier chassis to make sure they are 

plugged all the way in.

 

  Check the ground wire connection to make sure it is tightly secured to the proper ground in the vehicle.

 

 

Symptom 

Possible Cause 

Solution 

No Subwoofer Output 

Fuse not installed in inline fuse 

holder on subwoofer and/or 

amplifier power harness 

Install fuse into fuse holder.  

Refer to instructions for correct 

placement 

Low battery voltage 

Recharge the battery 

Negative battery cable not 

connected 

Reconnect negative battery 

cable 

Power wire connector not 

connected to body harness 

Connect power wire to body 

harness.  Check for loose 

connection 

Ground wire not grounded properly  Check ground wire with voltmeter 

to insure it is a good ground 

Balance and/or fader controls not 

set to neutral position 

Set balance and fader control to 

center settings.  (only affects 

stand-alone subwoofer kit) 

No low frequency information in 

music 

Test with several different songs 

Subwoofer harness not 

properly/completely connected to 

subwoofer 

Securely fasten both of the 

connectors on the subwoofer 

harness to the subwoofer.  

Check for loose connectors. 

Radio Not Coming On 

Blown radio fuse 

Refer to owner’s manual for radio 

fuse location and value 

Low battery voltage 

Recharge the battery 

Radio Comes On, But No 

Sound From Any Speakers 

Fuse not installed in inline fuse 

holder on amplifier harness 

Install fuse into fuse holder.  

Refer to instructions for correct 

placement 

Ground wire not grounded properly  Check ground wire with voltmeter 

to insure it is a good ground 

Low battery voltage 

Recharge the battery 

Содержание 19417166














Отзывы: